| Age | Commit message (Collapse) | Author |
|---|
|
Nautilus 2nd SKU has a leakage voltage at GPP_D0 in S5 state. We need to set this to LOW when entering S5 for clear the leakage.
BUG=None
BRANCH=poppy
TEST=Verified the leakage is gone after update coreboot
Change-Id: I054e707b2bc2e63d6f99cd2fd8a57be20615f111
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For supporting new SKU, we need to override GPIO table and device configuration.
The board ID of 2nd SKU of nautilus is started from 9, so we would determine SKU with it.
BUG=b:80052672
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7242f23f47010664cc29ea86a126e63c9dd62ccd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27147
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a file for uncore ASL code that is common among
Broadwell-DE mainboards but is currently copy + pasted in each of
their dsdt.asl files.
This is only for clean-up purposes. It is unclear if the code itself is
really necessary, but until we can do further investigation and testing
it will be left in.
Change-Id: I188e5e46dfa7c2ed3991fb97f2c1b5e062e2212d
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/27155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Collected timestamps indicate LZMA decompression of ramstage
is 4x slower when ROM is marked WP-cacheable, in contrast to
having ROM as US. A simple copy WP->WB with uncompressed
ramstage also appeared to be twice as slow as UC->WB copy.
It should be noted that if POSTCAR_STAGE was removed from build,
un-lzma takes 130 seconds instead of 45 milliseconds.
Change-Id: I2cf995395ef2d303ad0bc044dbfa160990a705d0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ic6e2a350a976a3fcb421d47a0bf5600df994edc2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This change fixes the following issues with EC_IN_RW signal:
1. EC_IN_RW is an input signal to the SoC. Configure it accordingly in
GPIO table for baseboard and bip.
2. GPIO_EC_IN_RW is passed in coreboot tables so that payload can
re-sample the GPIO at runtime.
BUG=b:110084012
TEST=Verified that EC_IN_RW signal is read correctly in depthcharge.
Change-Id: I1c5f5b4b914ced98e89a571dc398df5ba1fe8460
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change adds Synaptics device to phaser project.
BUG=b:110236590
TEST=emerge-octopus coreboot chromeos-bootimage
reflash the coreboot to DUT,make sure the Synaptics Touchpad can work.
Change-Id: Icc1e8c35a9de54ed04187fcf219a72a592d3bd81
Signed-off-by: Xingyu <wuxy@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27159
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add LinuxBoot support
* Add u-root mode
* Download kernel and u-root from upstream sources.
* Add customization options
* Clean kernel only if directory exists
Change-Id: I3a25ff6812e046acc688cbbb203cf262ad751659
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23071
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add support for parsing and booting FIT payloads.
* Build fit loader code from depthcharge.
* Fix coding style.
* Add Kconfig option to add compiletime support for FIT.
* Add support for initrd.
* Add default compat strings
* Apply optional devicetree fixups using dt_apply_fixups
Starting at this point the CBFS payload/ can be either SELF or FIT.
Tested on Cavium SoC: Parses and loads a Linux kernel 4.16.3.
Tested on Cavium SoC: Parses and loads a Linux kernel 4.15.0.
Tested on Cavium SoC: Parses and loads a Linux kernel 4.1.52.
Change-Id: I0f27b92a5e074966f893399eb401eb97d784850d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
* Add documentation for CN81XX SoC
* Add documentation for CN81XX EVB SFF mainboard
* Add documentation for BDK
* Add documentation for BOOTROM and BOOTBLOCK behaviour
* Alphabetically sort vendors
Change-Id: Ibfcd42788e31f684baed658dc3c4dfe1b8e4f354
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Import from https://chromium.googlesource.com/chromiumos/platform/depthcharge
Coding style and coreboot integration will be done in a separate commit.
Change-Id: Iee56db328d7eeffb0eaf829841243b0b9195c199
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Set the payload argument in selfload, as other (non self) payloads, are
going to set a different argument.
Change-Id: I994f604fc4501e0e3b00165819f796b1b8275d8c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25861
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to schematic, we need to correct USB OC pin configuration.
- OC0 for Type-C Port 1
- OC1 for Type-C Port 0
- OC2 for Type-A Port
- OC3 to NC
BUG=NONE
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ic71baef646926cc6aadcc5dda7cb14f00e8d3687
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds ACPI properties for SYTS7817 device.
BUG=b:110013532
Change-Id: Ifdec4efce169c066f212a393df21089d43d8e4d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This creates a fleex variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:110085182
TEST=None
Change-Id: Ia8b8bb757f67bea997b7f43489c38cac62f7682d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27105
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The endian conversion function be32toh() is defined in
src/include/endian.h, however this file is not used for cbfstool
compilation. Currently the one provided by the host is used and if the
host does not provide this endian.h file, the build will fail.
However, we do have endian conversion functions in commonlib/endian.h
which is available for cbfstool compilation.
Switch from be32toh() to read_be32() in order to avoid relying on a
host provided include file.
We use functions from commonlib/endian.h already in cbfstool.
Change-Id: I106274cf9c69e1849f848920d96a61188f895b36
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/27116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Boot tested on asus/p2b-ls and p2b-ds.
Change-Id: I0154f1d120bef3b45286fb4314f0de419cd8341e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/26821
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I96f42d5dc10d36855bdca64d1406a254250ee5b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26820
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I323426e0d9ddee1be72d15702fee4f92c7b348cc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This moves CAR stack under variable MTRRs and removes
old CAR code that used complex fixed MTRRs and placed
stack in low memory.
Change-Id: I75ec842ae3b6771cc3f7ff652adbe386c03b9a5f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/26586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
These CAR init files are no longer used.
The _ht variant will be used as basis for P3 CAR
using with variable MTRRs so we only move file.
Change-Id: Iace8762c11e2f282df1850f7be170c841d4881f4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27084
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DEVEN defines are wrong, but weren't used at all.
Fix them as they are needed by the hybrid_graphics_driver and
use the defines instead of magic values.
Tested on Lenovo T410: The IGD turns on with the correct value.
Change-Id: Idf9fc0115de5c72f7d5d88cbb09ae1d2fee0afd0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fix coding style.
Change-Id: Id13c0ee284293c0c06d46c75c850bc7e81cfc1f6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The dram controller cannot fully initialize the dram on warm
reset (receive enable calibration consistently fails) therefore
requiring cached timings.
This option is mostly useful when rebooting after having flashed a new
rom which overwrites the mrc cache region.
Change-Id: I405c0eca076fe081641ede9a670f734c98cbf8fc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is a small 8 megabit (1 MiB) part.
Change-Id: I9890457d0d14beb17d0a428c2701e620ae8c2512
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
All Grunt variants should identify as grunt in SMBIOS so that
they're recognized correctly as a unibuild Grunt variant.
BUG=b:110244268
TEST=Careena identifies as grunt
Change-Id: Iaf254149fbec9551d9220018d6d6a0a1be741538
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27117
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I69b014430802de132c8d9b6c8409bc762b995468
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27093
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This pin does not have a native function for eSPI. Nonetheless if we use
eSPI, it should be configured as a GPIO and kept unconnected to allow
S0ix entry.
Also removed initialization of LPC pins in mainboard code as they are
already initialized in chipset code. The settings fpr LPC pins in
chipset code were updated to those that were previously in mainboard
code and have been validated on LPC flavor of Geminilake RVP.
BUG=b:79251613
BRANCH=none
TEST=From kernel prompt in bip, type powerd_dbus_suspend.
Check on EC console that SOC enters S0ix.
Change-Id: Ie0c1013fee638a3b7a91469736efc0c25a1597fa
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23742
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support booting a GNU/Linux payload on non x86, the FIT format
should be used, as it is the defacto standard on ARM.
Due to greater complexity of FIT it is not converted to simple ELF format.
Add support for autodecting FIT payloads and add them as new CBFS_TYPE 'fit'.
The payload is included as is, with no special header.
The code can determine the type at runtime using the CBFS_TYPE field.
Support for parsing FIT payloads in coreboot is added in a follow on
commit.
Compression of FIT payloads is not supported, as the FIT sections might be
compressed itself.
Starting at this point a CBFS payload/ can be either of type FIT or SELF.
Tested on Cavium SoC.
Change-Id: Ic5fc30cd5419eb76c4eb50cca3449caea60270de
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update dptf.asl and TCC parameters from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI
Change-Id: Ic0ffc169ad3939cacb46824ed23999c61a23d2c4
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable keyboard backlight by Careena SKUID
Set to 10% as the same as google/snappy project
BUG=b:110065836
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I7d302c4f50528b0e6b7ef4d990f342a69cff34f5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Tested on Google peppy (Acer C720).
Change-Id: I6453c40bf4ebe4695684c1bd3a403d6def82814f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ifb8aa43b6545482bc7fc136a90c4bbaa18d46089
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/22957
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I595198d66193c63f6c80c39371fbec10065d2165
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ib5d574347373009c8021597f555e6e86c2c0c41f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3544ce4a573b6996d64b140d8acdaeb3de430896
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I6919845965d90fe8a20a07748ae4804fed0d0cef
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27013
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: I4843f52307b87cff6fa6f4d0c74b87428fefa8ac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
TESTED Intel DG41WV with VGA, Intel DG43GT with VGA and HDMI1 and
HDMI2.
Change-Id: I774b79cc0ef9dc72ccf48901ab94376b27ed9c7a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some things were coding errors, other things need to be fsb specific.
Most things here don't seem to matter all that much but better to get
it right.
Change-Id: I1afa637a16a083c3a945ba3e2a71292b005736fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It looks like this hardware has a bug where the display controller
does not work properly when dram is clocked 533MHz and the channels
are configured in non-stacked mode.
The workaround is to select stacked mode in this configuration.
Change-Id: I6f37ce15a4e98a4cdbd6d893f22846a65c8be021
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
There seems to be a hardware bug where the combination of non-stacked
channel settings, both channels populated and 533MHz dram speed cause
the display to be unusable.
The code to actually select stacked mode based on hardware
configuration will be add in a followup patch.
This patch does the following:
* Add option to the sysinfo struct for stacked mode
* Fix programming channel 1 DRB which needs special care for the last
populated rank in stacked mode
TESTED on Intel dg41wv (with stacked mode hardcoded and dram at 533MHz)
Change-Id: I95965bfea129b37f64163159fefa1c8f16331b62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I630d49ab504d9f6e052806b516a600fa41b9a8da
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use of device_t is deprecated.
Change-Id: I6adc0429ae9ecc8f726d6167a6458d9333dc515f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I9cebfc5c77187bd81094031c43ff6df094908417
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
GSMI Set Event Log is taking more than 1K in stack. This causes the
stack to overflow into the adjacent stack. This has the side effect of
causing any CPU waiting for the SMI handler to complete to crash when
the lock is unlocked because the return pointer has been smashed.
BUG=b:80539294
TEST=built on grunt and tested by running `halt` from the OS.
Change-Id: Ib170c7d03909ef3d20831726b285178a75007b06
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27033
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stoneyridge is running into a stack overflow in the SMM handler.
BUG=b:80539294
TEST=built on grunt
Change-Id: I94e385497bd93c3638c69fb08d9b843c3bbb55ce
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27034
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_E2 will be used as a BT reset line, so configure GPP_E2 as an
output and initialize it high (high = out of reset).
BUG=b:80089559
BRANCH=none
TEST=none
Change-Id: If45ef3a592c389a0b80298c59eea849d07d9671e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FCAM_PWR_EN signal is changing to connect to GPP_B4 instead of
GPP_D8 as it needs a 3.3v gpio to provide enough power to also
directly power the camera LED.
BUG=b:79667559,b:78122599
BRANCH=none
TEST=none
Change-Id: Ie875ced45dfa2aa7069851004edde8f77329df34
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
C1E is disabled by the kernel driver intel_idle at boot. This does not
address the S3 resume case, so we lose state and C1E is enabled after S3
resume.
Disable C1E for GLK as it is for APL. This gives a coherent state before
and after S3 resume.
TEST='iotools rdmsr cpu 0x1fc'. Returns the same value after boot and S3
resume with bit [1] set to zero (0x20005d).
Change-Id: I437cbaca75c539c2bc5cd801ab8df907e7447d10
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Register 0x1fc (MSR_POWER_CTL) deserves a proper mask for the C1E
enable bit. Define POWER_CTL_C1E_MASK to be used subsequently.
Change-Id: I7a5408f6678f56540929b7811764845b6dad1149
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27035
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a method to retrieve a node's phandle.
Useful for board specific devicetree manipulations.
Change-Id: I966151ad7e82fc678ab4f56cf9b5868ef39398e0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Move generators for the board status report and the kconfig options
report into a common directory and wrap them in a docker container.
Also rework to emit HTML not wiki syntax.
Change-Id: If42e1dd312c5fa4e32f519865e3b551bc471bc72
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/26977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of checking each directory in series, kick off the checks
in parallel and then wait for them to finish. Failures print out with
file information, so mixing output isn't a problem. This reduces
the time it takes to run on lumberingbuilder by 60%.
This could probably be sped up even more by splitting up src/mainboard
into smaller sections.
This method does skip a few control files at the top level - .gitignore,
.checkpatch.conf, gnat.adc, etc. These could be added to the list of
files to check, but I didn't think it was needed.
Change-Id: I171977e713a9956cf4142cfc0a199e10040abb35
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/27011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Per PCI specification, function 0 must be present,
so functions 1 to 7 can be skipped in this case.
For a device that is not multi-function, it may not
decode function number in the hardware at all. To
avoid registering such a device eight times, skip
scanning functions 1 to 7.
Without the latter fix, a single-function PCI bridge
may call pci_scan_bus() second time and secondary
side devices would get appended second time in the
array devices[]. At that point, quicksort() apparently
hits an infinite recursion loop.
Since pci_scan_bus() is called in part of the early
modules->init() sequence early in main(), the errors
here left coreinfo payload completely silent when
PCI module was built-in on affected system.
Terminal screen was cleared, though.
Change-Id: Ifc6622f050b98afb7196de0cc3a863c4cdfa6c94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
With platforms moved to RELOCATABLE_RAMSTAGE, these
overrides no longer have a meaning.
Overrides existed because AGESA ramstage did not fit within
the default 1 MiB of RAMTOP - RAMBASE, when placed low.
Change-Id: I0185875dc550de74877c94f36128d5979e5553d6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26813
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4571e8b560559b3d7afe429eca8caa1512e244a8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the two ranges to be used for the new callouts, AgesaHeapRebase
and AgesaGetHeapBaseInDram.
TEST=Boot grunt w/experimental blob, try different addresses
BUG=b:74518368
Change-Id: Ic7716794dc7d75f849e6e062865d6efbeb4292df
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Implement an optional callout for AgesaHeapRebase which allows AGESA
to override any internal hardcoded heap addresses.
Designate a region in CAR that may be used for pre-mem heap and return
that address before DRAM is configured. After DRAM is up, the address
in cbmem is returned.
TEST=Boot grunt with patchstack and experimental blob
BUG=b:74518368
Change-Id: Ieda202a6064302b21707bd7ddfabc132cd85ed45
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Implement a new AGESA callout that may be used to find the correct
temporary location in DRAM to store heap data.
Near the end of AmdInitPost, AGESA migrates its heap from a CAR-based
location to a temporary region. Once cbmem has been established, the
heap will be relocated again in AmdInitEnv from the temp location to
the final one.
This patch does not materially affect the behavior of AGESA's heap
management. It only puts coreboot in control of the location. Future
work may refactor the copying.
TEST=Boot grunt with patchstack and experimental blob
BUG=b:74518368
Change-Id: Ibc5cc988e3e80d78f50cf0195e952b657141e570
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a new callout definition for AgesaGetTempHeapBase and displace
AgesaHeapRebase (which was merged too soon) in the ordering. Also
add its structure.
AGESA will be modified to ask coreboot for the location for temporary
storage of heap data at the end of InitPost. The old methodology is
to use 0xb0000 but the change will allow coreboot to determine the
location.
BUG=b:74518368
Change-Id: I0bc894d7842cf4b3eb728a90704277b17f4bf7be
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic3808a0a10ddc8064d185e0920dcd9f60c435419
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After removing most geode_lx boards, some mainboard
directories are left empty. This patch cleans them up.
Change-Id: I2e99eba3d49dec90ceb2ce0c7f61612a9840ce59
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27092
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The -S flag of me_cleaner, in addition to the standard code removal,
sets the the AltMeDisable bit (ME 6.x-10.x) or the HAP bit (ME 11.x),
which asks Intel ME to stop the execution after the hardware
initialization.
This should bring some advantages:
* The state of Intel ME can be easily obtained by reading the Current
Operation Mode register to trigger specific adjustments in the
raminit (as already done in bd82x6x)
* Intel ME falls into a more defined state, instead of being in a
generic "Image Failure"
* Hopefully, less code is run by Intel ME, as the execution should
stop before even trying to load additional modules
Tested on:
* Nehalem, Sandy Bridge and Ivy Bridge (Nicola Corna)
* Broadwell, Skylake and Kabylake (Youness Alaoui)
If needed, the -S flag can be removed or integrated with other
board-specific options by overriding CONFIG_ME_CLEANER_ARGS.
Change-Id: I2c12d09124dcc39924d1dc4eaf53a2dc1f69a2ac
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/25508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
In preparation to allow devicetree overrides, it will be necessary to
use the same parsing functions to prepare two separate parse
trees. This change does the following things:
1. Updates root device and bus names to add base_ prefix.
2. Adds a function parse_devicetree that sets the root_parent and
linenum before calling yyparse().
3. Updates all uses of root_dev to refer to the next base_root_dev.
BUG=b:80081934
TEST=Verified that static.c generated for all boards built using
abuild is the same with and without this change.
Change-Id: I403a90c1ebf07ac66115ddfe137daf0980dc1a18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There are some acpigen functionality that have not been implemented. They
are defined as week within acpigen.c, in order to not break the build.
This adds stoneyridge specific versions.
BUG=b:79546790
TEST=Build grunt with added debug code to gpio_lib.asl. Boot to OS,
activate ACPI debug, activate S3 stress test. Interrupt stress test, do a
"cat /var/log/messages" saving the serial output. Examine the serial
output, see added debug code showing action taken. Confirm action by
reading proper register. Debug code removed.
Change-Id: I9062d889f828a3175b89e6f4a3659ebbf90eac68
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PM1 and GPE0 are being stored directly to NVS, when actually what should
be saved is the index of the bit responsible for waking. Fix the procedures
and add definitions to the actual IO addresses to be read when recording
status and enable registers.
BUG=b:75996437
TEST=Build and boot grunt. Once in OS, execute a sleep and a wake. See the
message indicating which indexes are being save in NVS for _SWS. Try sleep
stress test, verify that the index is different from that of power button.
Change-Id: I8bafc7bb7dd66e7f0eb8499e748535bbdcac5f53
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are some acpigen functionality that have not been implemented. In
order to implement them, ACPI GPIO functions to read and write to the
control MMIO of a particular pin is needed. So as a preliminary task to
implementing acpigen functions, create a library with functions to be
accessed by acpigen generated ACPI code.
BUG=b:79546790
TEST=Build grunt, more tests with commit 0f2acbd6b1.
Change-Id: I21c014b7f2698dd9193dae3113b18ee2a7303bcf
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is Garrett's patch with a bit of cleanup.
BUG=b:65442212
TEST=Was able to boot, suspend and resume on grunt.
Change-Id: I55959b59a4e60b679d959ebd77de27e5d454f5f7
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of checking each directory in series, kick off all the checks
in parallel and then wait for them to finish. Failures print out with
file information, so mixing output isn't a problem. This reduces
the time it takes to run on lumberingbuilder from 31 seconds to 6.
Change-Id: I1252a68a723370389d399f3d1a2aff3fad64c365
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/26995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This change checks to ensure that config is not NULL before it is
accessed for the first time.
Reported by: Coverity CID #1393312
Change-Id: Ic248c79783da9c2bfdf3b7f737e5963feff7558c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Change-Id: I0064710362a1c7882d5a40b469d6aacad5c60218
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/26964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Fix regression (supposedly) after commit:
23d62dd lib/bootmem: Add more bootmem tags
Without RELOCATABLE_RAMSTAGE, payload is allowed to overwrite
memory regions of the running ramstage. This case is handled
gracefully via a bounce-buffer implementation in arch/x86/boot.c.
Change-Id: I1c9bbdb963a7210d0817a7a990a70a1e4fc03624
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add bootmem_targets_usable_with_bounce() to handle
cases of payload loading via bounce-buffer.
Change-Id: I9ebbc621f8810c0317d7c97c6b4cdd41527ddcbb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26985
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Copy the script `scripts/config` from Linux (commit 427fbe89 (Merge
branch 'next' of
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux)) into the
newly created directory `scripts`. Here is the original commit message
from 2009.
> commit 8e54701ea85b0ab0971637825a628f5aa2b678a4
> Author: Andi Kleen <andi@firstfloor.org>
> Date: Sat Jan 3 03:21:41 2009 +0100
>
> kconfig: add script to manipulate .config files on the command line
>
> I often change single options in .config files. Instead of using
> an editor or one of the frontends it's convenient to do this from
> the command line. It's also useful to do from automated build scripts
> when building different variants from a base config file.
>
> I extracted most of the CONFIG manipulation code from one of my
> build scripts into a new shell script scripts/config
>
> The script is not integrated with the normal Kconfig machinery
> and doesn't do any checking against Kconfig files, but just manipulates
> that text format. This is always done at make time anyways.
>
> I believe this script would be a useful standard addition for scripts/*
>
> Sample usage:
>
> ./scripts/config --disable smp
> Disable SMP in .config file
>
> ./scripts/config --file otherdir/.config --module e1000e
> Enable E1000E as module in otherdir/.config
>
> ./scripts/config --state smp
> y
> Check state of config option CONFIG_SMP
>
> After merging into git please make scripts/config executable
>
> Signed-off-by: Andi Kleen <ak@linux.intel.com>
> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Change-Id: Ie32a4459398df8694956dd644f38692017a26388
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/26243
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib417f435011f0331a1b0228734874ef0a62fb587
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/26945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This also removes a "chapters mode" that we never used.
Change-Id: Ib301e2f4db0b9678081fa987a5dcc7108bb103a4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/26944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
SoCs from Skylake on have many settings as so called private con-
figuration registers (PCRs). These are organized as 256 ports with
a 64KiB space each. We use the Primary to Sideband (P2SB) bridge's
BAR to access them.
Change-Id: Iede4ac601355e2be377bc986d62d20098980ec35
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19593
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:80501386
BRANCH=none
TEST=timer and uart work fine
Change-Id: I08644892d34925574f791b000b0035d5afad7022
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/26722
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most things still need to be filled in, but this will allow us to build
boards which use this SOC.
BUG=b:80501386
BRANCH=none
TEST=timer and uart work fine
Change-Id: Ie81fa56ffce85188e1f9e979f9b0e64b764c2627
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/26659
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If1f032d097224a1102ba29d8d45dce46aad3a91a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I75fa4577055f25dde0a8b1044c005bba72cabd92
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
As a result of commit:
[711fb81] soc/intel/skylake: Swap PCI devfn resides in same PCI device
fizz's chip_info for the LAN driver is being overwritten/nulled, as the
LAN device is on function 2 (PCIe port 3), but the driver info was set
for the post-swapped PCIe port (1).
Move the driver chip_info to function 2/port 3, so that it follows the
PCI device function when swapped after FSP-s, and is correctly passed
to the LAN driver.
Test: boot google/fizz (teemo variant), check cbmem console and
verify ethernet MAC address and LED config correctly set.
Change-Id: I08810c0c89d99af5799f42c7c4e51814f09aafec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I2ea07cdeb8fc70dbf516831f4da5949fef136b37
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Why would that be a user visible option? Drop the prompt and the
`default n` and select it automatically when needed. I hope I
caught all its users.
TEST=Confirmed that systems with ELOG_GSMI or DEBUG_SMI compile
and link.
Change-Id: I44aeec530cc333f4ed4c8cfe67c7b5c9d8fb0049
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Clean it up and add all flash chip drivers to postcar stage thereby.
There seem to be SPI controllers that don't need the individual
flash chip drivers. For those postcar support was added in b6b1b23
(console/flashconsole: Enable support for postcar). However for
SPI controllers that need the individual drivers (i.e. those with
CONFIG_SPI_FLASH_INCLUDE_ALL_DRIVERS=y), linking of the postcar
stage was broken.
For all other stages, the set of compilation units stays the same.
Change-Id: Ib8bdb824bfcf2d31ac696e39f797c4355b765756
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26871
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Let the linker take care of it.
Change-Id: I67d2636ceb042f833c1b44888b98135d728940e0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This code is no longer needed.
BUG=b:107537694
TEST=Build & boot on grunt
Change-Id: I71ad01f0d4c69a618d564e514ed99550b72a6b44
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This code is no longer needed. Removing Kahlee options allows some
Kconfig options to be optimized.
BUG=b:77693343
TEST=Build Grunt, verify that nothing's changed.
Change-Id: I4eeeee7f35381bba8760c8a530251c475d0ee29b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The initial subsystem ID had a device ID but not a vendor ID.
This change adds the Google vendor ID to the subsystem ID.
Change-Id: I14897da115fd6f2ddd492b6c565bd23227197232
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/26987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Making exceptions for some payload to be loaded near
and under 1 MiB boundary sounds like a legacy 16-bit
x86 BIOS thing we generally do not want under lib/.
Change-Id: I8e8336a03d6f06d8f022c880a8334fe19a777f0a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add tablet motion control config to nami devices.
BUG=None
BRANCH=None
TEST=run evtest
make sure tablet switch value is 1 in tablet mode and 0
when not in tablet mode
Change-Id: Ie1480934dc003d9b467883e001ed89f9a3694d10
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26970
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- configure GPP_B7 (PCIE_NVME_CLKREQ_ODL) for NF1
- enable root port 9
- add nvme register settings to devicetree
BUG=b:78122599
BRANCH=chromeos-2016.05
TEST='emerge-nocturne depthcharge coreboot chromeos-bootimage',
boot to kernel, and verify /dev/nvme* entries exist.
CQ-DEPEND=CL:1090070
Change-Id: I0070d33b1ed09bd1f51a680d92ddb7e2bcb1ebc2
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
This patch removes BJ adapter configuration, which has been moved
to the EC.
BUG=b:109762580
CQ-DEPEND=CL:1089328
BRANCH=none
TEST=Verify BJ adapter is set expectedly on Teemo.
Change-Id: I3041b984e7f02624b94ba2713b084d001fa155f9
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1089370
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/26965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1a0db60b527c2f7ffe77743c0d75b78a7c8bc4cc
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/26877
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use of device_t has been abandoned in ramstage.
Use pci_devfn_t or pnp_devfn_t instead of device_t in romstage.
Change-Id: Ie0ae3972eacc97ae154dad4fafd171aa1f38683a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26984
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I07e00afbbd2c19cf3ea6e08f228eb39e45f1ad0c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I064ff5e76dd95c1770cd24139195b2a5fff2d382
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I775f5482970905134bb395b03845eb798d88d209
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
