| Age | Commit message (Collapse) | Author |
|---|
|
Fixes commit bd5b4aa683a634a73a6a63d1f197e2bb74b6a80e
"soc/intel/cannonlake: Switch PMC to use device callbacks" as it
requires the PCI device 1f.2 to be present in the devicetree.
It was missing for this mainboard and caused a boot failure.
Change-Id: Iaf508b2d955578efa2a266af50c568f5c0a47aaf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The MIPI source video data has a large variation (e.g. 59Hz ~ 61Hz),
anx7625 defines K ratio for matching MIPI input video clock and
DP output video clock. A bigger k value can match a bigger video data
variation. IVO panel has smaller variation than DP CTS spec, so decrease
k value to 0x3b.
BUG=b:194659777
BRANCH=none
TEST=Display is normal on Asurada
Change-Id: If3a09811999babda45e9a9a559dd447920109204
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This patch unifies line indentation.
Change-Id: Ieeb580057d8abb20afe3a5d73f5f835e6d31c899
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The ANX7625 display bridge requires customized
hs_da_trail time.
This patch is based on CB:51433 (commit 6482b16,
"mb/google/kukui: fine tune the data lane trail")
BUG=b:198558237
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: I0eedb8fa6a1b3dfd9619c7cbf755c9c4071a8484
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add mipi panel support for mrbland
- Setup gpio and modify LCD sequence.
- Use the following panel for mrbland:
AUO B101UAN08.3
BOE TV101WUM-N53
- Use panel_id to distinguish which mipi panel to use.
BUG=b:195516474,b:197300875,b:197300876
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: Ib7cd2da429b114bf6bad5af312044a0f01319b46
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57336
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Our MIPI panel initialization framework differentiates between DCS and
GENERIC commands, but the exact interpretation of those terms is left to
the platform drivers. In practice, the MIPI DSI transaction codes for
these are standardized and platforms always need to do the same
operation of combining the command length and transfer type into a
correct DSI protocol code. This patch factors out the various
platform-specific DSI protocol definitions into a single global one and
moves the transaction type calculation into the common panel framework.
The Qualcomm SC7180 implementation which previously only supported DCS
commands is enhanced to (hopefully? untested for now...) also support
GENERIC commands. While we're rewriting that whole section also fix some
other issues about how exactly long and short commands need to be passed
to that hardware which we identified in the meantime.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I09ade7857ca04e89d286cf538b1a5ebb1eeb8c04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This patch adds new board type BOARD_TYPE_ULT_ULX_T4 and changes
BOARD_TYPE_SERVER value to 8.
BUG=b:199359579
BRANCH=None
TEST=Build and boot brya
Change-Id: I48eb0785a209499ee0d90bd541376d9bbacf2390
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
The headers added are generated as per FSP v2347_00.
Previous FSP version was v2265_01.
Changes include:
- UserBd UPD description update in FspmUpd.h
BUG=b:199359579
BRANCH=None
TEST=Build and boot brya
Change-Id: I5e4dd58e5fb1a744b035a4de96986053a02610d3
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The USB descriptions are flipped. Fix by inverting the USB descriptions
in devicetree.
BUG=None
TEST=Build
BRANCH=None
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I4b33f4de137536c5f3592380da15f6b3a3633bf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57538
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a short documenting comment to each usb entry in devicetree so it is
clear which function each usb port maps to.
BUG=None
TEST=Build
BRANCH=None
Change-Id: I14cbb6af021bb27c89aa82456722f21aa09617be
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56725
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Moves MAX_EVENT_SIZE to commonlib/bsd/include, and renames it
ELOG_MAX_EVENT_SIZE to give it an "scoped" name.
The moving is needed because this defined will be used from
util/cbfstool (see next CL in the chain).
BUG=b:172210863
TEST=compiles Ok
Change-Id: I86b06d257dda5b325a8478a044045b2a63fb1a84
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adds "clear" command to cbfsutil/elogtool tool.
"clear" clears the RW_ELOG region by using either:
* flashrom if no file is provided
* or using file write if an input file is provided.
The region is filled with ELOG_TYPE_EOL. And a
ELOG_TYPE_LOG_CLEAR event is inserted.
Additionally, it does a minor cleanup to command "list", like:
* use buffer_end()
* add "list" to the cmds struct
* and make elog_read() very similar to elog_write()
Usage:
$ elogtool clear
BUG=b:172210863
TEST=elogtool clear && elogtool list
elogtool clear -f invalid.raw
elogtool clear -f valid.raw
Change-Id: Ia28a6eb34c82103ab078a0841b022e2e5e430585
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
|
|
After switching to runtime generation of the Intel Power Engine (PEPD)
device, this file is no longer required.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I2444433f08bfda6f79589a397a2ad2b5a3ecb0ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch skylake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7c7cb424278946a9767ea329d18fb03d4e57dce8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to get rid of pep.asl, skylake also needs to support runtime
generation of the Intel Power Engine, therefore add this support to
devices that have a discoverable PMC as well.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4bf0c4a338301b335fa78617e0f2ed5a9f4360ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch elkhartlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I47f03b440729d4b37ae0abc84bd1d18c4e01657d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch jasperlake boards to this method.
soc/intel/jasperlake: Switch to acpigen PEPD
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib7f17f9b3b1396708ba68fa7a6d199d6e8b0ba11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch cannonlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic5343b0fd37eafac29a23846c8cfc3ca93d1821d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Now that the PMC device is marked as hidden in devicetrees, the device
callbacks can be used instead of BOOT_STATE_INIT_ENTRY callbacks.
Note that this moves PMC initialization from BS_DEV_INIT_CHIPS to
BS_DEV_ENUMERATE, which aligns with other Intel SoCs.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If292728ad975ba803fed6abea879f6f634470a11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FSP-S hides the PMC from the PCI bus when it runs, but there are still
initialization steps coreboot programs for the PMC. Therefore, change
all of the cannonlake mainboards to set the PMC as hidden in the
devicetree, which means the device will be skipped during enumeration,
but device callbacks are still issued as if the device were enabled.
TEST=Ran full patch train on google/dratini, disassembled SSDT and the
PEPD device matches what is in pep.asl. Also verified via dmesg that the
INT33A1 device is still initialized by the kernel.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib4a20ce9075ce7653388a5d3e281fe774bf89355
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch tigerlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8e97c589273e934e89d69d8829680b9cac1ff9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The LPM enable mask is useful to have in more than one place, therefore
more the get_disable_mask() function and its helpers to lpm.c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ibe83dc106f5f37baf9d5c64f68c47d85ea4e6dd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56460
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The pep.asl file is being obsoleted by runtime generation, therefore
switch alderlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I617bc3d1c3cf4ac6b6cbbd790dcf62e731024834
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds support for the S0ix UUID in the Intel Power Engine _DSM
method. This allows the ACPI tables to expose device/IP power states
requirements for different system low power states
BUG=b:185437326
TEST=Along with following patch on brya0 after resume from s0ix,
cat /sys/kernel/debug/pmc_core/substate_requirements
Element | S0i2.0 | S0i3.0 | Status |
USB2PLL_OFF_STS | Required | Required | Yes |
PCIe/USB3.1_Gen2PLL_OFF_STS | Required | Required | Yes |
PCIe_Gen3PLL_OFF_STS | Required | Required | Yes |
OPIOPLL_OFF_STS | Required | Required | Yes |
OCPLL_OFF_STS | Required | Required | Yes |
MainPLL_OFF_STS | | Required | |
MIPIPLL_OFF_STS | Required | Required | Yes |
Fast_XTAL_Osc_OFF_STS | | Required | |
AC_Ring_Osc_OFF_STS | Required | Required | Yes |
SATAPLL_OFF_STS | Required | Required | Yes |
XTAL_USB2PLL_OFF_STS | | Required | Yes |
CSME_PG_STS | Required | Required | Yes |
SATA_PG_STS | Required | Required | Yes |
xHCI_PG_STS | Required | Required | Yes |
UFSX2_PG_STS | Required | Required | Yes |
OTG_PG_STS | Required | Required | Yes |
SPA_PG_STS | Required | Required | Yes |
SPB_PG_STS | Required | Required | Yes |
SPC_PG_STS | Required | Required | Yes |
THC0_PG_STS | Required | Required | Yes |
THC1_PG_STS | Required | Required | Yes |
GBETSN_PG_STS | Required | Required | Yes |
GBE_PG_STS | Required | Required | Yes |
LPSS_PG_STS | Required | Required | Yes |
ADSP_D3_STS | | Required | Yes |
xHCI0_D3_STS | Required | Required | Yes |
xDCI1_D3_STS | Required | Required | Yes |
IS_D3_STS | Required | Required | Yes |
GBE_TSN_D3_STS | Required | Required | Yes |
CPU_C10_REQ_STS_0 | Required | Required | Yes |
CNVI_REQ_STS_6 | | Required | Yes |
ISH_REQ_STS_7 | | Required | Yes |
MPHY_Core_DL_REQ_STS_16 | Required | Required | Yes |
Break-even_En_REQ_STS_17 | Required | Required | Yes |
Auto-demo_En_REQ_STS_18 | Required | Required | Yes |
Int_Timer_SS_Wake0_Pol_STS | Required | Required | |
Int_Timer_SS_Wake1_Pol_STS | Required | Required | |
Int_Timer_SS_Wake2_Pol_STS | Required | Required | |
Int_Timer_SS_Wake3_Pol_STS | Required | Required | |
Int_Timer_SS_Wake4_Pol_STS | Required | Required | |
Int_Timer_SS_Wake5_Pol_STS | Required | Required | |
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I542290bd5490aa6580a5ae2b266da3d78bc17e6b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56005
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iebd994a46e870e42431d0fc71dd14b1c2b01f9aa
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57536
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie859490d3cb3b8c56437cbd6c3e46525c580d3f4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57535
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is a use-case for generating the AML bytecode at runtime for the
Intel Power Engine device, which comes in a followup patch.
BUG=b:185437326
TEST=verified on google/brya and google/dratini by dumping SSDT and
verifying the PEPD device matches what was previously in the DSDT:
Scope (\_SB.PCI0)
{
Device (PEPD)
{
Name (_HID, "INT33A1")
Name (_CID, EisaId ("PNP0D80")
Method (_DSM, 4, Serialized)
{
ToBuffer (Arg0, Local0)
If ((Local0 == ToUUID ("c4eb40a0-6cd2-11e2-bcfd-0800200c9a66")))
{
ToInteger (Arg2, Local1)
If ((Local1 == Zero))
{
Return (Buffer (One)
{
0x63
})
}
If ((Local1 == One))
{
Return (Package (0x01)
{
Package (0x03)
{
\NULL,
Zero,
Package (0x02)
{
Zero,
Package (0x02)
{
0xFF,
Zero
}
}
}
})
}
If ((Local1 == 0x02)){}
If ((Local1 == 0x03)){}
If ((Local1 == 0x04)){}
If ((Local1 == 0x05))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (One)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (One)
}
If (CondRefOf (\_SB.PCI0.EGPM))
{
\_SB.PCI0.EGPM ()
}
}
If ((Local1 == 0x06))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (Zero)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (Zero)
}
If (CondRefOf (\_SB.PCI0.RGPM))
{
\_SB.PCI0.RGPM ()
}
}
Return (Buffer (One)
{
0x00
})
}
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie83722e0ed5792e338fc5c39a57eef43b7464e3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since the value returned by _DSM function 0 for a given UUID is trivial
to calculate, add the ability to do so to the
acpigen_write_dsm() functions.
Change-Id: Id9be050442485b42202cf91649aa94e56f35032a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the get_supported_lpm_states() function to set the respective FSP
UPD.
TEST=with patchtrain on brya0,
/sys/kernel/debug/pmc_core/substate_requirements shows only the
substates that are applicable to the design (S0i2.0, S0i3.0).
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I5bb8b3671e78c5f2706db2d3a21b25cf90a14275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This function searches the known MCH device IDs for Alder Lake and
returns the appropriate enum value representing ADL-P, ADL-M, ADL-S, or
unknown.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I26354b340e0c5f15ba246c1cb831d7feaf62d2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The ANX7625 needs explicit LINE_END to output proper
display data.
This patch is based on CB:51435 (commit b923931,
"mb/google/kukui: Add flag for MIPI_DSI_MODE_LINE_END ANX7625")
BUG=b:198558237
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: Id5666fa1bcf96002725509d7436ea1ff5febef93
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57486
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some bridge chips or panels require DSI signal output
before the DSI receiver is ready to work.
This patch is based on CB:47380 (commit b32e4d6,
"mb/google/kukui: Add panel api after dsi start")
BUG=b:198558237
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: Id72560caee9352f88db2de7269b1472f56ac1bdf
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57485
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On some platforms, runtime firmware crashes write logs to the CBMEM
console. For those, since a crash reboots the system, by the time we
have a chance to run `cbmem` again the boot where the crash happened
will be the one before the "last" (current) boot. So cbmem -1 doesn't
show the interesting part, and cbmem -c potentially shows a lot that is
cumbersome to dig through. This patch introduces a new option cbmem -2
to explicitly show only the boot cycle before the last one.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6725698f4c9ae07011cbacf0928544cebb4ad6f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
This reverts commit b90e6fdd25f7fcc9db6be50a0b117a7509c6fdb1. Latest
releases of PSP does not load PSP verstage on S0i3 resume. Hence no need
to skip PSP verstage on S0i3 resume.
BUG=b:196400450
TEST=Build and boot to OS in Guybrush. Trigger a suspend/resume cycle
and then a reboot and ensure that the system boots to OS.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Iaeb92edb69662e6c06f4d0e3d7b760d4597bf650
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
ELAN TS: eKT3644
BUG=b:194961444
TEST=emerge-guybrush coreboot chromeos-bootimage
TS is functional
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id1601efbbe419bb28233a2678fdde005a55da671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
ALC5682-VD/ALC5682-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ib458cf47909a2d7a65f086c5f30f85a16f78d589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add the pin definitions for the remote GPIOs and the GPIO pin mux values
for the GPIO mode of those pins. For now, accessing the remote GPIOs is
only supported from the native coreboot code running on the x86 cores
and not from verstage on PSP or ACPI.
BUG=b:194524995
TEST=On Majolica with a Cezanne APU configuring GPIO 262 as output and
then toggling that GPIO in an infinite loop in the mainboard's bootblock
code results in GPIO 262 toggling as expected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0e57042e74da88503b36d6065e9500876287f8bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Right now the ACPI code doesn't support accessing the remote GPIO block
yet, so don't generate invalid remote GPIO access functions and warn
about those being unsupported.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id364a59c9650bf4e3633b494b01ab23c0bbc50b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
Some AMD SoCs have a 5th GPIO bank, the remote GPIO bank, which isn't
located right after the 4th GPIO bank, but instead at a different
location inside the APCIMMIO region. A difference to the first 4 GPIO
banks is that the corresponding GPIO MUX registers aren't in a separate
bank, but at the end of the remote GPIO region. So this remote GPIO
region only supports 48 GPIOs with a 32 bit configuration register each
and has the 8 bit GPIO MUX registers beginning at offset 0xc0 in the
remote GPIO region.
For now using the remote GPIOs from verstage on PSP isn't supported. To
support this, it would need to map acpimmio_remote_gpio and update the
pointer like it already does for acpimmio_gpio0, acpimmio_iomux and a
few others.
BUG=b:194524995
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic8d7ff677a99381a5558782b80b0c4cae67602db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
As per the connectivity document deny list entry size should be uint16
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
Fixes: cc50770cd0("wifi: Add support for wifi time average SAR config")
Change-Id: I045c21350cf4c2266df108eede6350d090322ba0
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update the GPIO configuration to match the latest schematic.
BUG=b:192370253
BRANCH=None
TEST=FW_NAME=kano emerge-brya coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I96be95a127f42b005d97a3c02650af13419524a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
According to the schematic diagram of version C14_MB_20210902A_SB,
modify the settings of GPIO and fw_config.
BUG=b:197700276
BRANCH=none
TEST=emerge-brya coreboot
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I14907faeb631193715b1e0e451e427fb79a68279
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
According to config.star fw mask definition, add initial FW_CONFIG id.
BUG=b:194649740
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Cq-Depend: chrome-internal:4072654
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Ifef750338d777b76e9710d6bca9a166120db6a0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Default VBOOT_HASH_BLOCK_SIZE is 1 KiB and increasing it to 4 KiB
helps in improving overall boot time since it reduces hashing and
body loading time.
Increasing it over 4 KiB doesn't result in significant improvement,
thus keeping the value at 4 KiB as of now.
Timing data:
Note that before Data is with 1 KiB block size.
|------------------------------------------------------|
| Stage | Block Size | Before | After |
|finished loading body| 4 KiB | 205,187 | 189,947 |
|finished loading body| 8 KiB | 205,187 | 188,708 |
|finished loading body| 16 KiB | 205,187 | 188,085 |
|finished loading body| 32 KiB | 205,187 | 187,793 |
|------------------------------------------------------|
BUG=b:188577893
BRANCH=None
TEST=Boot time for Brya improves by 20 - 25 msec
Change-Id: I9222761c7d58e4a370d3a41c651b6c169599d792
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change sets Irms config in FSP if TdcTimeWindow and TdcCurrentLimit
is set to non zero. It results VR TDC Input current to be treated as it
is root mean square.
This change also optimizes the check of TdcTimeWindow and TdcCurrentLimit
for TdcEnable UPD.
BRANCH=None
TEST=Build and boot brya with debug FSP and verify Irms UPD value
from logs
Change-Id: Ice5c775ef9560503109957a1ed994af1d287aafc
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This is already done in drivers/intel/fsp2_0/Makefile.inc.
Change-Id: Idfd15d0a9d2cb15e613881f80bb25c18bd7454bb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I7e575cb17e2004bd931f4fa1d05f17c4cdca29ba
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I550198aae22fbe39f4b461332a10de82c78cd191
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57498
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Compute the bit width of FADT register blocks using their length in
bytes, which is readily available from a different field.
Change-Id: I4dafa3546714ae46946d6502598e4b945c2a77a0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
From ACPI specification, version 6.2 Errata A:
A `duty_width` value of 0 indicates that processor duty cycle is not
supported and the processor continuously runs at its base frequency.
Because Broadwell sets `duty_width` to 0, processor duty cycle is not
supported, and the value of `duty_offset` is ignored. For consistency
with Lynx Point, set `duty_offset` to 0.
Change-Id: I68cb85ec32a6cceda0cea29d76df6c6219b78a40
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Currently coreboot for the AMD SOCs only supports accessing the up to 4
main GPIO banks of up to 64 GPIOs each. Some AMD SoCs including Cezanne
have another GPIO bank in the ACPIMMIO region that can contain up to 48
GPIOs beginning with GPIO 256 which is called the remote GPIO bank. The
first 48 DWORDs of that ACPIMMIO bank are the 32 bit wide GPIO registers
and beginning at offset 0xc0 it has the corresponding 8 bit wide GPIO
MUX registers.
BUG=b:194524995
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ice4e3358de17ac2601621814978cdb70e6f2c926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add and use the I2C_RESET_SCL_PIN macro for populating the i2c_scl_pins
array that is used for the sb_reset_i2c_peripherals call to bring the
I2C buses into a defined state.
TEST=Timeless build results in identical image for Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifedc09d0bf745545fa0510df7d5037f02b9012a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Retype loop variable `i` to `uint32_t` for consistency with the types of
the `number_of_phases` and `phase_index` struct fields and the parameter
of the `platform_fsp_multi_phase_init_cb()` function.
Change-Id: I82916f33c2dc5dab6a31111c9acba2a18a5cfb0b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57491
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for this part.
MT53E512M32D1NP-046 WT:B
BUG=b:199032134
TEST=emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Ic9ccee7c0957119a69ee179854cf13d30db40621
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team and Intel suggestion.
BUG=b:198249129
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I25d3909144d6e38d7a6eb859d33585c319a84b04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Coverity detects dereference pointers req and res that are NULL when
calling the pmc_send_ipc_cmd function. This change prevents NULL
pointers dereference.
Found-by: Coverity CID 1458068, 1458070, 1458971, 1458073, 1458075,
1458076
TEST=None
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ib88fa5f44dd33ad1ad2e763d79438b5c5b78acb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Setting the usb_phy version and length in the soc code instead of devicetree.
That way the devicetree code does not have to reapeat it for different
AMD Cezanne based systems.
Tested on guybrush by changing phy settings in devicetree and then checking
the usb phy register.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: I2db49e095672054b9b15042fb003a93b67e3a4c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The AMD Cezanne FSP expects a usb phy config structure ID of 0xd 0x6.
If the ID does not match, the FSP USB will not set up the phy.
Tested on guybrush by changing phy settings in devicetree and then checking
the usb phy register.
Cq-Depend: chrome-internal:4087511
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: I4fdb5af1cbc3c70cc113ef6f0fd9332e1a27f142
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The update_efs_spi_speed allows changing the SPI speed manually in a
binary that has already been built. This will allow binaries not built
for the EM100 SPI ROM emulator to be updated so that they will work.
There is a corresponding change that will check to see if the EFS value
has been modified from the original speed and will prevent coreboot from
updating the SPI speed and mode.
BUG=b:177233017
TEST=Update SPI speed in existing binary. See that SPI speed has
changed.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I905a9fd8bd93a28aab927dffecbbcf24934b9e03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56644
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Even though `device` entries are children of `chip` entries in the
devicetree source format, the chips in the translated C structures
are only hooked up to device nodes. Hence, any chip with all its
settings will be silently dropped by sconfig if there is no device
node below it.
Let's adapt the parser to ensure that there is at least one `device`
entry. The intermediate `chipchildren_dev` rule applies until the
first `device` entry is found, then everything continues as before
with the `chipchildren` rule.
Change-Id: I54830bc1fc7d00a0605f3fe4d36a83ef57ef3312
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51119
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable SaGv support for redrix
BUG=b:198536984
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I54402dfde5db4106a4e0d891c19592fda39a1099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on commit b9c22e09 (util/sconfig: Compare probe conditions for override device match), add fw_config probe for ALC5682I-VS headphone Audio Codec.
BUG=b:197546020
BRANCH=dedede
TEST=ALC5682I-VD/VS and CS42l42 work normally according fw_config
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Iac09663b095e758f1bc0cfaf7adb6e84d203788a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57105
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All `chip` entries need a device node below them to actually get hooked
up. Add a dummy generic device like other instances of this driver use.
Change-Id: Ifbb5c9a6b389a2c809ce654d584d5197af764893
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57475
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Ricoh bridge device is actually on the external PCI bus. To make the
driver configuration usable, also add a PCI device below it.
Change-Id: I58a25da9d676a19b47e8b88438152bc247c024b4
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57474
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: Ib9e6019b6f316c1b176da1592514dcdcaf8c505a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57473
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: Ia5c573e582dab542b2a2a969c17581b0da6ed74e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57472
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: I91c98f66951de5301f72754a24a92168862820a2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57471
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: I4781d6afdcd92f21872f3059b417483107129bf4
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57470
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: I244cd5d91af9413b338de0e8ee2480d9744ea077
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57469
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries always need a device node below them to actually get
hooked up.
Change-Id: Ie84694f586351ce327c8df9338e96377825ad7c7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57468
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add missing device nodes as the `chip` entry needs one to actually
get hooked up.
Change-Id: If34f4919a5499b3148c7e4408cc753fbd909693a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57467
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To take any effect, a `chip` entry in a devicetree or overridetree
always needs a `device` node.
Change-Id: I158459e28dc8c63df4f1d58b30017868a57e5602
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57466
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was no code attached to this driver and hence one couldn't hook
it up to any device. Even if mentioned in the `devicetree.cb` it was
still dead code.
Change-Id: I12415ea9e0120b1d00524f8f39f9b2d02f46ba05
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update the telemetry setting for guybrush
vddcrvddfull_scale_current : 94648 #mA
ddcrvddoffset : 785
vddcrsocfull_scale_current : 30314 #mA
vddcrsocoffset : 560
BUG=b:189157660
TEST=Build
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I19ba3d69be63d0f8491d15ee48ce9ba468a46fdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set GPIO GPP_A8 as high to enable EN_PP3300_TOUCHSCREEN.
also reduce enable delay time for meet panel power sequence.
BUG=b:197668845
BRANCH=volteer
TEST=FW_NAME=chronicler emerge-volteer coreboot chromeos-bootimage
Verify no corruption is seen on the screen
panel power sequence meet spec
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I9a0c1d0afafb2c446fcb3d18e1a67573218614e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57103
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code under `cpu/x86/tsc` is only compiled in when its `Makefile.inc`
is included from platform (CPU/SoC) code and the `UDELAY_TSC` Kconfig
option is enabled.
Include `cpu/x86/tsc/Makefile.inc` once from `cpu/x86/Makefile.inc` and
drop the now-redundant inclusions from platform code. Also, deduplicate
the `UDELAY_TSC` guards.
Change-Id: I41e96026f37f19de954fd5985b92a08cb97876c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57456
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow to select the primary graphics device between the IGD and the
external PCIe GPU depending on the ONBOARD_VGA_IS_PRIMARY config.
The option sets the priority only. This means that if a high priority
is set for an external PCI device and it is not connected/not enabled,
then the device with a lower priority will be used, in our case it is
IGD.
TEST = Set PRIMARY_PCI and boot Linux on the Kontron mAL10 [1] with
the miniPCIe video adapter on the Silicon Motion SM750 controller. As
a result, the display connected to an external GPU device shows the
Tianocore logo + setup menu and the desktop.
[1] https://review.coreboot.org/c/coreboot/+/39133
Change-Id: Idcd117217cf412ee0722aff52db4b3c8ec2a226c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Update generic id to generate the SSDT1 acpi table successfully
BUG=b:196866470
BRANCH=firmware-zork-13434.B
TEST=generate SSDT1 acpi table by command "iasl -d SSDT1"
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I09c9adc2db08e8e3905d9ba800948252230e4d54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The eventlog requires RTC to provide correct timestamps, so we have to
turn on the config and add the common drivers.
BUG=b:199003609
TEST=check timestamp in 'mosys eventlog list'
BRANCH=none
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Change-Id: Ia382cd023fcbfdf2c1efeb7b32c0b99feb71effa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
A chip entry in the devicetree is not hooked up without a device
beneath it. It seems the intention was to leave these superio
drivers unconfigured, so there should be no harm to turn the
entries into comments.
Change-Id: I6b606f35eba089b74c562084772d95be41cac39c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
1. Disable external output reset signal in first WDT reset
to preserve WDT original reset reason for WDT issue in kernel stage.
2. After preserved WDT reset reason, do fully reset again by sending
external output reset signal.
BUG=b:194025005
TEST=boot to kernel ok and function test pass
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.corp-partner.google.com>
Change-Id: I5887a8312f4daab3cbd0a30fea0195670a932e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add Kconfig option TIANOCORE_ABOVE_4G_DECODE to pass build option to
edk2 to enable or disable "Above 4G Decode". Disabling allows certain Linux
distributions to boot such as Qubes, Zorin and Proxmox.
Requires commit `2f6d4cbcc7fa49462e607baed7626524ccd59ad3` that is
present in the `uefipayload_202107` branch of MrChromebox's edk2
repository.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia3b1d15196c0ec611431af29031682fea626d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Suggested-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0016a6c7d6581cb261cab6178268c1a86b89c839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56831
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since both functions are only called from one function each, inline them
into those functions. Also get_gpio_mux just returned the return value
of iomux_read8, so there were two functions with identical functionality
which shouldn't be the case.
Suggested-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5662d0226edb25a9954fa47b42e208729a79e5a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56830
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This aligns the GPIO MUX access more with the GPIO control register
access and will facilitate adding support for the remote GPIO bank. Also
change the GPIO number argument type to gpio_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4054656c5cc23ea942e8dd370fbbffca304755d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Introduce amdblocks/acpimmio_legacy_gpio100.h so that the old pre-SoC
chipsets can still access the raw GPIO100 and IOMUX ACPIMMIO registers
while only allowing GPIO accesses through the GPIO API on the SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18872dfa40d53ba8b0d7802eec52ede5e2ae617a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move those two functions near the top of the file to have all functions
that do the hardware accesses in one place.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If787e6e1d124a932beafd73e5ce7d0ce4869e800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Use unsigned integers for variables that aren't supposed to become
negative.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ee037221b9818b0474fe0376323e522c1b3b516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7cf9cbd2a287dcfe3a47a8a6b164c2b3d8ae95d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since the raw GPIO MMIO register access is now only used inside the
gpio_banks block, the gpio_read32 and gpio_write32 functions can be
moved to that block to reduce the visibility and enforce the usage of
the functions provided by the gpio_banks block.
The iomux_read8 and iomux_write8 functions can't be easily moved to the
gpio_banks block, since it's also used in the pre-SOC AMD chipsets that
use the ACPIMMIO access functions directly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia0d6dea72c6bebbbe6ce545bedfc74f91e0042c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7d7a8c5a7188fd558a577352f8b246e61f3edd63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The I2C code should use some GPIO API to access the GPIO registers
instead of accessing the GPIO MMIO regions itself.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I84dff381ad86e0c7f879f0f079186aec9cafc604
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
No need to do raw GPIO MMIO accesses when basically the same
functionality can be achieved by using existing APIs. Using the existing
GPIO API instead of raw GPIO MMIO register accesses allows containing
all direct GPIO MMIO accesses inside the common AMD GPIO code which will
be done in subsequent patches. Since the value parameter of gpio_set is
int, change the type of the val parameter of drive_scl to int as well
even though I'm not sure why a signed integer was used for this in the
common GPIO API. Since program_gpios already configures the SCL GPIOs as
outputs, gpio_set can be used in drive_scl which only sets the output
value, but doesn't configure the direction.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks similar to the same as before during the reset_i2c_peripherals
call, but due to the additional overhead of the read-modify-write to the
GPIO register instead of just a write, the pulse width gets about 50%
longer. Since the udelay call in drive_scl still has an open TODO to
make this configurable and the pulses being longer is in the safe side,
this side-effect can be addressed in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic323cebc1c83ecd6f0e1fbab419c69489d77face
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
drive_scl in soc/amd/common/block/i2c/i2c.c writes the raw GPIO MMIO
configuration register and drives it as output, so don't initially
configure the GPIO as input with no pull up/down. This is a preparation
to use the common AMD GPIO access functions instead of the raw register
accesses, since the gpio_set function only sets the output value, but
doesn't reconfigure the direction. Using gpio_output there instead would
reconfigure the direction as well, but would result in doubling the
number of MMIO accesses, so just configure the GPIOs correctly right
away to avoid that.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks exactly the same as before during the reset_i2c_peripherals call.
This was probed at the SCL pad of the unpopulated I2C level shifter on
the side that is connected to the SoC.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8e94afe0c755a02abcc722d5094e220d8781f8f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56807
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update fw_config.c based on the schematic carbine_adl-p_evt_20210901.pdf
BUG=b:190688567
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I240c0cd777d215e46a0a661aaac63a187311019d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
NVMe needs extra time to run boot process, enable power and deassert reset for NVMe earlier in the boot flow that gimble can successfully boot into OS with non-serial coreboot.
BUG=b:198405404
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ib76965db2a6cd0c19be4043fec73af297a619c7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57359
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables SaGv support for gimble.
BUG=b:198531517
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I29887418827614afb10558c6958c9c5e9667079e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marx Wang <marx.wang@intel.com>
|
|
Roughly half the boards had a "title" comment for the board. This adds
it for the rest of the boards to make everything consistent.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ib941318842136212727f56fc6130381c5c9cd55b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
copy config from guybrush reference board.
remove wwan & speaker amp due to the different solution is
used on nipperkin.
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I58a9b8393a965a9c793802d3e660829863b74375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Verified by running following on vendor
and observing mPCIe USB device (dis)appearing:
echo 1 > /sys/bus/pci/devices/0000:00:16.0/remove
echo 1 > /sys/bus/pci/devices/0000:00:16.2/remove
echo 1 > /sys/bus/pci/devices/0000:00:00.0/rescan
Change-Id: I6ee7e3679c9cd87b81f955c68ec89db1dda30aec
Signed-off-by: Sebastian 'Swift Geek' Grzywna <swiftgeek@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
