diff options
Diffstat (limited to 'src/mainboard/bitworks')
| -rw-r--r-- | src/mainboard/bitworks/ims/Config.lb | 136 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/Options.lb | 156 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/auto.c | 154 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/chip.h | 5 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/cmos.layout | 74 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/debug.c | 66 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/failover.c | 32 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/irq_tables.c | 32 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/mainboard.c | 12 | ||||
| -rw-r--r-- | src/mainboard/bitworks/ims/reset.c | 43 |
10 files changed, 710 insertions, 0 deletions
diff --git a/src/mainboard/bitworks/ims/Config.lb b/src/mainboard/bitworks/ims/Config.lb new file mode 100644 index 0000000000..357a1013ff --- /dev/null +++ b/src/mainboard/bitworks/ims/Config.lb @@ -0,0 +1,136 @@ +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The linuxBIOS bootloader. +## +default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +## +## Set all of the defaults for an x86 architecture +## + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +#if HAVE_PIRQ_TABLE object irq_tables.o end +#object reset.o + +## +## Romcc output +## +makerule ./failover.E + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" +end + +makerule ./failover.inc + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" +end + +makerule ./auto.E + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" +end +makerule ./auto.inc + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" +end + +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds + +## +## Build our reset vector (This is where linuxBIOS is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +### Should this be in the northbridge code? +mainboardinit arch/i386/lib/cpu_reset.inc + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + ldscript /arch/i386/lib/failover.lds + mainboardinit ./failover.inc +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +mainboardinit cpu/x86/fpu/enable_fpu.inc +mainboardinit cpu/x86/mmx/enable_mmx.inc +mainboardinit ./auto.inc +mainboardinit cpu/x86/mmx/disable_mmx.inc + +## +## Include the secondary Configuration files +## +dir /pc80 +config chip.h + +chip northbridge/intel/i440bx + device pci_domain 0 on + end + + chip cpu/intel/socket_PGA370 + end + +end + diff --git a/src/mainboard/bitworks/ims/Options.lb b/src/mainboard/bitworks/ims/Options.lb new file mode 100644 index 0000000000..a67e1495cb --- /dev/null +++ b/src/mainboard/bitworks/ims/Options.lb @@ -0,0 +1,156 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses HAVE_OPTION_TABLE +uses USE_OPTION_TABLE +uses CONFIG_ROM_STREAM +uses IRQ_SLOT_COUNT +uses MAINBOARD +uses MAINBOARD_VENDOR +uses MAINBOARD_PART_NUMBER +uses LINUXBIOS_EXTRA_VERSION +uses ARCH +uses FALLBACK_SIZE +uses STACK_SIZE +uses HEAP_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses _RAMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses HAVE_MP_TABLE +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses CONFIG_CONSOLE_SERIAL8250 +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses CONFIG_UDELAY_TSC + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE = 512*1024 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## no MP table +## +default HAVE_MP_TABLE=0 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=0 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=0 +default IRQ_SLOT_COUNT=4 +#object irq_tables.o + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=0 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 +default FALLBACK_SIZE = 131072 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default USE_OPTION_TABLE = 0 + +default _RAMBASE = 0x00004000 + +default CONFIG_ROM_STREAM = 1 + +## +## The default compiler +## +default CROSS_COMPILE="" +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=9 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=9 + +default CONFIG_UDELAY_TSC=1 + +end + diff --git a/src/mainboard/bitworks/ims/auto.c b/src/mainboard/bitworks/ims/auto.c new file mode 100644 index 0000000000..c841d61044 --- /dev/null +++ b/src/mainboard/bitworks/ims/auto.c @@ -0,0 +1,154 @@ +#define ASSEMBLY 1 + +#include <stdint.h> +#include <device/pci_def.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <arch/hlt.h> +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" +#include "ram/ramtest.c" +#include "southbridge/intel/i440bx/i440bx_early_smbus.c" +#include "superio/NSC/pc87351/pc87351_early_serial.c" +#include "northbridge/intel/i440bx/raminit.h" +#include "cpu/x86/mtrr/earlymtrr.c" +#include "cpu/x86/bist.h" + +#define SERIAL_DEV PNP_DEV(0x2e, PC87351_SP1) + +/* + */ +void udelay(int usecs) +{ + int i; + for(i = 0; i < usecs; i++) + outb(i&0xff, 0x80); +} + +#include "debug.c" +#include "lib/delay.c" + + +static void memreset_setup(void) +{ +} + +/* + static void memreset(int controllers, const struct mem_controller *ctrl) + { + } +*/ + + +static void enable_mainboard_devices(void) +{ + device_t dev; + /* dev 0 for southbridge */ + + dev = pci_locate_device(PCI_ID(0x1106,0x8231), 0); + + if (dev == PCI_DEV_INVALID) { + die("Southbridge not found!!!\n"); + } + pci_write_config8(dev, 0x50, 7); + pci_write_config8(dev, 0x51, 0xff); +#if 0 + // This early setup switches IDE into compatibility mode before PCI gets + // // a chance to assign I/Os + // movl $CONFIG_ADDR(0, 0x89, 0x42), %eax + // // movb $0x09, %dl + // movb $0x00, %dl + // PCI_WRITE_CONFIG_BYTE + // +#endif + /* we do this here as in V2, we can not yet do raw operations + * to pci! + */ + dev += 0x100; /* ICKY */ + + pci_write_config8(dev, 0x42, 0); +} + +static void enable_shadow_ram(void) +{ + device_t dev = 0; /* no need to look up 0:0.0 */ + unsigned char shadowreg; + /* dev 0 for southbridge */ + shadowreg = pci_read_config8(dev, 0x63); + /* 0xf0000-0xfffff */ + shadowreg |= 0x30; + pci_write_config8(dev, 0x63, shadowreg); +} + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + unsigned char c; + c = smbus_read_byte(device, address); + return c; +} + + +#include "northbridge/intel/i440bx/raminit.c" +#include "sdram/generic_sdram.c" +//#include "sdram/generic_dump_spd.c" + +static void main(unsigned long bist) +{ + static const struct mem_controller cpu[] = { + { + .channel0 = { + (0xa << 3) | 0, + (0xa << 3) | 1, + (0xa << 3) | 2, (0xa << 3) | 3, + }, + } + }; + unsigned long x; + + if (bist == 0) { + early_mtrr_init(); + } + pc87351_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + + /* Halt if there was a built in self test failure */ + report_bist_failure(bist); + + enable_smbus(); +// dump_spd_registers(&cpu[0]); + +#if 0 + enable_shadow_ram(); + /* + memreset_setup(); + this is way more generic than we need. + sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu); + */ + sdram_set_registers((const struct mem_controller *) 0); + sdram_set_spd_registers((const struct mem_controller *) 0); + sdram_enable(0, (const struct mem_controller *) 0); +#endif + + /* Check all of memory */ +#if 0 + ram_check(0x00000000, msr.lo); +#endif +#if 0 + static const struct { + unsigned long lo, hi; + } check_addrs[] = { + /* Check 16MB of memory @ 0*/ + { 0x00000000, 0x01000000 }, +#if TOTAL_CPUS > 1 + /* Check 16MB of memory @ 2GB */ + { 0x80000000, 0x81000000 }, +#endif + }; + int i; + for(i = 0; i < sizeof(check_addrs)/sizeof(check_addrs[0]); i++) { + ram_check(check_addrs[i].lo, check_addrs[i].hi); + } +#endif +} diff --git a/src/mainboard/bitworks/ims/chip.h b/src/mainboard/bitworks/ims/chip.h new file mode 100644 index 0000000000..d0fe923429 --- /dev/null +++ b/src/mainboard/bitworks/ims/chip.h @@ -0,0 +1,5 @@ +extern struct chip_operations mainboard_bitworks_ims_ops; + +struct mainboard_bitworks_ims_config { + int nothing; +}; diff --git a/src/mainboard/bitworks/ims/cmos.layout b/src/mainboard/bitworks/ims/cmos.layout new file mode 100644 index 0000000000..5ba4c032c1 --- /dev/null +++ b/src/mainboard/bitworks/ims/cmos.layout @@ -0,0 +1,74 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +1008 16 h 0 check_sum + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM + +checksums + +checksum 392 1007 1008 + + diff --git a/src/mainboard/bitworks/ims/debug.c b/src/mainboard/bitworks/ims/debug.c new file mode 100644 index 0000000000..7eeabdef47 --- /dev/null +++ b/src/mainboard/bitworks/ims/debug.c @@ -0,0 +1,66 @@ + +static void print_debug_pci_dev(unsigned dev) +{ + print_debug("PCI: "); + print_debug_hex8((dev >> 16) & 0xff); + print_debug_char(':'); + print_debug_hex8((dev >> 11) & 0x1f); + print_debug_char('.'); + print_debug_hex8((dev >> 8) & 7); +} + +static void print_pci_devices(void) +{ + device_t dev; + for(dev = PCI_DEV(0, 0, 0); + dev <= PCI_DEV(0, 0x1f, 0x7); + dev += PCI_DEV(0,0,1)) { + uint32_t id; + id = pci_read_config32(dev, PCI_VENDOR_ID); + if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0x0000)) { + continue; + } + print_debug_pci_dev(dev); + print_debug("\r\n"); + } +} + +static void dump_pci_device(unsigned dev) +{ + int i; + print_debug_pci_dev(dev); + print_debug("\r\n"); + + for(i = 0; i <= 255; i++) { + unsigned char val; + if ((i & 0x0f) == 0) { + print_debug_hex8(i); + print_debug_char(':'); + } + val = pci_read_config8(dev, i); + print_debug_char(' '); + print_debug_hex8(val); + if ((i & 0x0f) == 0x0f) { + print_debug("\r\n"); + } + } +} + +static void dump_pci_devices(void) +{ + device_t dev; + for(dev = PCI_DEV(0, 0, 0); + dev <= PCI_DEV(0, 0x1f, 0x7); + dev += PCI_DEV(0,0,1)) { + uint32_t id; + id = pci_read_config32(dev, PCI_VENDOR_ID); + if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0x0000)) { + continue; + } + dump_pci_device(dev); + } +} diff --git a/src/mainboard/bitworks/ims/failover.c b/src/mainboard/bitworks/ims/failover.c new file mode 100644 index 0000000000..bdcb9eaed2 --- /dev/null +++ b/src/mainboard/bitworks/ims/failover.c @@ -0,0 +1,32 @@ +#define ASSEMBLY 1 +#include <stdint.h> +#include <device/pci_def.h> +#include <device/pci_ids.h> +#include <arch/io.h> +#include "arch/romcc_io.h" +#include "pc80/mc146818rtc_early.c" + +static unsigned long main(unsigned long bist) +{ + /* This is the primary cpu how should I boot? */ + if (do_normal_boot()) { + goto normal_image; + } + else { + goto fallback_image; + } + normal_image: + asm volatile ("jmp __normal_image" + : /* outputs */ + : "a" (bist) /* inputs */ + : /* clobbers */ + ); + cpu_reset: + asm volatile ("jmp __cpu_reset" + : /* outputs */ + : "a"(bist) /* inputs */ + : /* clobbers */ + ); + fallback_image: + return bist; +} diff --git a/src/mainboard/bitworks/ims/irq_tables.c b/src/mainboard/bitworks/ims/irq_tables.c new file mode 100644 index 0000000000..894c27dec5 --- /dev/null +++ b/src/mainboard/bitworks/ims/irq_tables.c @@ -0,0 +1,32 @@ +/* This file was generated by getpir.c, do not modify! + (but if you do, please run checkpir on it to verify) + Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up + + Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM +*/ + +#include <arch/pirq_routing.h> + +const struct irq_routing_table intel_irq_routing_table = { + PIRQ_SIGNATURE, /* u32 signature */ + PIRQ_VERSION, /* u16 version */ + 32+16*5, /* there can be total 5 devices on the bus */ + 0, /* Where the interrupt router lies (bus) */ + 0x88, /* Where the interrupt router lies (dev) */ + 0x1c20, /* IRQs devoted exclusively to PCI usage */ + 0x1106, /* Vendor */ + 0x8231, /* Device */ + 0, /* Crap (miniport) */ + { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ + 0x5e, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ + { + /* 8231 ethernet */ + {0,0x90, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}}, 0x1, 0}, + /* 8231 internal */ + {0,0x88, {{0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}}, 0x2, 0}, + /* PCI slot */ + {0,0xa0, {{0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}, {0x2, 0xdeb8}}, 0, 0}, + {0,0x50, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x3, 0}, + {0,0x98, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x4, 0}, + } +}; diff --git a/src/mainboard/bitworks/ims/mainboard.c b/src/mainboard/bitworks/ims/mainboard.c new file mode 100644 index 0000000000..28f46e700b --- /dev/null +++ b/src/mainboard/bitworks/ims/mainboard.c @@ -0,0 +1,12 @@ +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <device/pci_ops.h> +#include <arch/io.h> +#include "chip.h" + +struct chip_operations mainboard_bitworks_ims_ops = { + CHIP_NAME("Bitworks IMS mainboard ") +}; + diff --git a/src/mainboard/bitworks/ims/reset.c b/src/mainboard/bitworks/ims/reset.c new file mode 100644 index 0000000000..5796e17dc8 --- /dev/null +++ b/src/mainboard/bitworks/ims/reset.c @@ -0,0 +1,43 @@ +#if 0 +//#include "arch/romcc_io.h" +#include <arch/io.h> + +typedef unsigned device_t; + +#define PCI_DEV(BUS, DEV, FN) ( \ + (((BUS) & 0xFF) << 16) | \ + (((DEV) & 0x1f) << 11) | \ + (((FN) & 0x7) << 8)) + +static void pci_write_config8(device_t dev, unsigned where, unsigned char value) +{ + unsigned addr; + addr = dev | where; + outl(0x80000000 | (addr & ~3), 0xCF8); + outb(value, 0xCFC + (addr & 3)); +} + +static void pci_write_config32(device_t dev, unsigned where, unsigned value) +{ + unsigned addr; + addr = dev | where; + outl(0x80000000 | (addr & ~3), 0xCF8); + outl(value, 0xCFC); +} + +static unsigned pci_read_config32(device_t dev, unsigned where) +{ + unsigned addr; + addr = dev | where; + outl(0x80000000 | (addr & ~3), 0xCF8); + return inl(0xCFC); +} + +#include "../../../northbridge/amd/amdk8/reset_test.c" + +void hard_reset(void) +{ + set_bios_reset(); + pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1); +} +#endif |