1 files changed, 0 insertions, 157 deletions
diff --git a/src/mainboard/bitworks/ims/Options.lb b/src/mainboard/bitworks/ims/Options.lb
deleted file mode 100644
index 0c13bf6683..0000000000
--- a/src/mainboard/bitworks/ims/Options.lb
+++ /dev/null
@@ -1,157 +0,0 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
-uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
-uses LINUXBIOS_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_PAYLOAD_START
-uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
-uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses CONFIG_UDELAY_TSC
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE  = 512*1024
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## no MP table
-##
-default HAVE_MP_TABLE=0
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=0
-default IRQ_SLOT_COUNT=4
-#object irq_tables.o
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=0
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-
-default _RAMBASE = 0x00004000
-
-default CONFIG_ROM_PAYLOAD     = 1
-
-##
-## The default compiler
-##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
-
-##
-## The Serial Console
-##
-
-# To Enable the Serial Console
-default CONFIG_CONSOLE_SERIAL8250=1
-
-## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
-
-# Select the serial console base port
-default TTYS0_BASE=0x3f8
-
-# Select the serial protocol
-# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
-
-##
-### Select the linuxBIOS loglevel
-##
-## EMERG      1   system is unusable               
-## ALERT      2   action must be taken immediately 
-## CRIT       3   critical conditions              
-## ERR        4   error conditions                 
-## WARNING    5   warning conditions               
-## NOTICE     6   normal but significant condition 
-## INFO       7   informational                    
-## DEBUG      8   debug-level messages             
-## SPEW       9   Way too many details             
-
-## Request this level of debugging output
-default  DEFAULT_CONSOLE_LOGLEVEL=9
-## At a maximum only compile in this level of debugging
-default  MAXIMUM_CONSOLE_LOGLEVEL=9
-
-default CONFIG_UDELAY_TSC=1
-
-end
-