Revision: linuxbios@linuxbios.org--devel/freebios--devel--2.0--patch-36

Creator:  Li-Ta Lo <ollie@lanl.gov>

emulator update

Correction to the reduce emulator from Paulo


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

4 files changed, 176 insertions, 552 deletions

diff --git a/src/southbridge/via/vt8231/Config.lb b/src/southbridge/via/vt8231/Config.lb
index b0b2ef5abf..46b4e26129 100644
--- a/src/southbridge/via/vt8231/Config.lb
+++ b/src/southbridge/via/vt8231/Config.lb
@@ -1,2 +1,8 @@
 config chip.h
-object vt8231.o
+driver vt8231.o
+driver vt8231_lpc.o
+driver vt8231_acpi.o
+driver vt8231_ide.o
+driver vt8231_nic.o
+#driver vt8231_usb.o
+
diff --git a/src/southbridge/via/vt8231/chip.h b/src/southbridge/via/vt8231/chip.h
index bc1e445f26..fef4e2913b 100644
--- a/src/southbridge/via/vt8231/chip.h
+++ b/src/southbridge/via/vt8231/chip.h
@@ -4,18 +4,10 @@
 extern struct chip_operations southbridge_via_vt8231_ops;
 
 struct southbridge_via_vt8231_config {
-	/* PCI function enables */
-	/* i.e. so that pci scan bus will find them. */
-	/* I am putting in IDE as an example but obviously this needs
-	 * to be more complete!
-	 */
-	int enable_ide;
-	/* enables of functions of devices */
-	int enable_usb;
+	/* enables of Non-PCI devices */
 	int enable_native_ide;
 	int enable_com_ports;
 	int enable_keyboard;
-	int enable_nvram;
 };
 
 #endif /* _SOUTHBRIDGE_VIA_VT8231 */
diff --git a/src/southbridge/via/vt8231/vt8231.c b/src/southbridge/via/vt8231/vt8231.c
index d78bb2cf86..514d0c0626 100644
--- a/src/southbridge/via/vt8231/vt8231.c
+++ b/src/southbridge/via/vt8231/vt8231.c
@@ -1,441 +1,73 @@
-
-#include <arch/io.h>
+#include <console/console.h>
 #include <device/device.h>
 #include <device/pci.h>
 #include <device/pci_ops.h>
 #include <device/pci_ids.h>
-#include <console/console.h>
+
+#include <pc80/mc146818rtc.h>
+#include <pc80/keyboard.h>
+
 #include "vt8231.h"
 #include "chip.h"
 
-void pc_keyboard_init(void);
+/* Base 8231 controller */
+static device_t lpc_dev;
 
-void hard_reset(void) 
+void hard_reset(void)
 {
-	printk_err("NO HARD RESET ON VT8231! FIX ME!\n");
-}
-
-static void usb_on(int enable)
-{
-	unsigned char regval;
-
-	/* Base 8231 controller */
-	device_t dev0 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
-	/* USB controller 1 */
-	device_t dev2 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, 0);
-	/* USB controller 2 */
-	device_t dev3 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, dev2);
-	
-	/* enable USB1 */
-	if(dev2) {
-		if (enable) {
-			pci_write_config8(dev2, 0x3c, 0x05);
-			pci_write_config8(dev2, 0x04, 0x07);
-		} else {
-			pci_write_config8(dev2, 0x3c, 0x00);
-			pci_write_config8(dev2, 0x04, 0x00);
-		}
-	}
-	
-	if(dev0) {
-		regval = pci_read_config8(dev0, 0x50);
-		if (enable) 
-			regval &= ~(0x10);    
-		else
-			regval |= 0x10;    	      
-		pci_write_config8(dev0, 0x50, regval);
-	}
-	
-	/* enable USB2 */
-	if(dev3) {
-		if (enable) {
-			pci_write_config8(dev3, 0x3c, 0x05);
-			pci_write_config8(dev3, 0x04, 0x07);
-		} else {
-			pci_write_config8(dev3, 0x3c, 0x00);
-			pci_write_config8(dev3, 0x04, 0x00);
-		}
-	}
-	
-	if(dev0) {
-		regval = pci_read_config8(dev0, 0x50);
-		if (enable) 
-			regval &= ~(0x20);    
-		else
-			regval |= 0x20;    
-		pci_write_config8(dev0, 0x50, regval);
-	}
+        printk_err("NO HARD RESET ON VT8231! FIX ME!\n");
 }
 
 static void keyboard_on(void)
 {
 	unsigned char regval;
-	
-	/* Base 8231 controller */
-	device_t dev0 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
-	
-	/* kevinh/Ispiri - update entire function to use 
-	   new pci_write_config8 */
 
-	if (dev0) {
-		regval = pci_read_config8(dev0, 0x51);
+	if (lpc_dev) {
+		regval = pci_read_config8(lpc_dev, 0x51);
 		regval |= 0x0f; 
-		pci_write_config8(dev0, 0x51, regval);
+		pci_write_config8(lpc_dev, 0x51, regval);
 	}
 	init_pc_keyboard(0x60, 0x64, 0);
 }
 
-static void nvram_on(void)
+static void com_port_on(void)
 {
-	/*
-	 * the VIA 8231 South has a very different nvram setup than the 
-	 * piix4e ...
-	 * turn on ProMedia nvram.
-	 * TO DO: use the PciWriteByte function here.
-	 */
-	
-	/*
-	 * kevinh/Ispiri - I don't think this is the correct address/value
-	 * intel_conf_writeb(0x80008841, 0xFF);
+#if 0
+	// enable com1 and com2. 
+	enables = pci_read_config8(dev, 0x6e);
+	
+	/* 0x80 is enable com port b, 0x10 is to make it com2, 0x8
+	 * is enable com port a as com1 kevinh/Ispiri - Old code
+	 * thought 0x01 would make it com1, that was wrong enables =
+	 * 0x80 | 0x10 | 0x8 ; pci_write_config8(dev, 0x6e,
+	 * enables); // note: this is also a redo of some port of
+	 * assembly, but we want everything up.
 	 */
-}
-
 
-/*
- * Enable the ethernet device and turn off stepping (because it is integrated 
- * inside the southbridge)
- */
-static void ethernet_fixup()
-{
-	device_t	edev;
-	uint8_t		byte;
-
-	printk_info("Ethernet fixup\n");
-
-	edev = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_7, 0);
-	if (edev) {
-		printk_debug("Configuring VIA LAN\n");
-		
-		/* We don't need stepping - though the device supports it */
-		byte = pci_read_config8(edev, PCI_COMMAND);
-		byte &= ~PCI_COMMAND_WAIT;
-		pci_write_config8(edev, PCI_COMMAND, byte);
-	} else {
-		printk_debug("VIA LAN not found\n");
-	}
-}
-
-
-/* we need to do things in this function so that PCI scan will find 
- * them.  One problem here is that we can't use ANY of the new device 
- * stuff. This work here precedes all that.      
- * Fundamental problem with linuxbios V2 architecture.
- * You can't do pci control in the C code without having done a PCI scan.
- * But in some cases you need to to pci control in the c code before doing
- * a PCI scan. But you can't use arch/romcc_io.h (the code you need) because
- * that has functions with the same name but different type signatures
- * (e.g. device_t). This needs to get fixed. We need low-level pci scans
- * in the C code. 
- */
-static void vt8231_pci_enable(struct southbridge_via_vt8231_config *conf) 
-{
-	/*
-	  unsigned long busdevfn = 0x8000;
-	  if (conf->enable_ide) {
-	  printk_debug("%s: enabling IDE function\n", __FUNCTION__);
-	  }
-	*/
-}
-
-/* PIRQ init
- */
-void pci_assign_irqs(unsigned bus, unsigned slot, const unsigned char pIntAtoD[4]);
-
-
-static const unsigned char southbridgeIrqs[4] = { 11, 5, 10, 12 };
-static const unsigned char enetIrqs[4] = { 11, 5, 10, 12 };
-static const unsigned char slotIrqs[4] = { 5, 10, 12, 11 };
-
-/*
-	Our IDSEL mappings are as follows
-	PCI slot is AD31          (device 15) (00:14.0)
-	Southbridge is AD28       (device 12) (00:11.0)
-*/
-static void pci_routing_fixup(struct device *dev)
-{
-
-	printk_info("%s: dev is %p\n", __FUNCTION__, dev);
-	if (dev) {
-		/* initialize PCI interupts - these assignments depend
-		   on the PCB routing of PINTA-D 
-
-		   PINTA = IRQ11
-		   PINTB = IRQ5
-		   PINTC = IRQ10
-		   PINTD = IRQ12
-		*/
-		pci_write_config8(dev, 0x55, 0xb0);
-		pci_write_config8(dev, 0x56, 0xa5);
-		pci_write_config8(dev, 0x57, 0xc0);
-	}
-
-	// Standard southbridge components
-	printk_info("setting southbridge\n");
-	pci_assign_irqs(0, 0x11, southbridgeIrqs);
-
-	// Ethernet built into southbridge
-	printk_info("setting ethernet\n");
-	pci_assign_irqs(0, 0x12, enetIrqs);
-
-	// PCI slot
-	printk_info("setting pci slot\n");
-	pci_assign_irqs(0, 0x14, slotIrqs);
-	printk_info("%s: DONE\n", __FUNCTION__);
-}
-
-
-void
-dump_south(void)
-{
-	device_t dev0;
-	dev0 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
-	int i,j;
-	
-	for(i = 0; i < 256; i += 16) {
-		printk_debug("0x%x: ", i);
-		for(j = 0; j < 16; j++) {
-			printk_debug("%02x ", pci_read_config8(dev0, i+j));
-		}
-		printk_debug("\n");
-	}
+	/* set com1 to 115 kbaud not clear how to do this yet.
+	 * forget it; done in assembly.
+	 */
+#endif
 }
 
-static void vt8231_init(struct southbridge_via_vt8231_config *conf)
+/* FixME: to be removed ? */
+static void vt8231_enable(struct device *dev)
 {
-	unsigned char enables;
-	device_t dev0;
-	device_t dev1;
-	device_t devpwr;
-	
-	// to do: use the pcibios_find function here, instead of 
-	// hard coding the devfn. 
-	// done - kevinh/Ispiri
-	printk_debug("vt8231 init\n");
-	/* Base 8231 controller */
-	dev0 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
-	/* IDE controller */
-	dev1 = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, 0);
-	/* Power management controller */
-	devpwr = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231_4, 0);
-
-	// enable the internal I/O decode
-	enables = pci_read_config8(dev0, 0x6C);
-	enables |= 0x80;
-	pci_write_config8(dev0, 0x6C, enables);
-	
-	// Map 4MB of FLASH into the address space
-	pci_write_config8(dev0, 0x41, 0x7f);
-	
-	// Set bit 6 of 0x40, because Award does it (IO recovery time)
-	// IMPORTANT FIX - EISA 0x4d0 decoding must be on so that PCI 
-	// interrupts can be properly marked as level triggered.
-	enables = pci_read_config8(dev0, 0x40);
-	pci_write_config8(dev0, 0x40, enables);
-	
-	// Set 0x42 to 0xf0 to match Award bios
-	enables = pci_read_config8(dev0, 0x42);
-	enables |= 0xf0;
-	pci_write_config8(dev0, 0x42, enables);
-	
-	// Set bit 3 of 0x4a, to match award (dummy pci request)
-	enables = pci_read_config8(dev0, 0x4a);
-	enables |= 0x08;
-	pci_write_config8(dev0, 0x4a, enables);
-	
-	// Set bit 3 of 0x4f to match award (use INIT# as cpu reset)
-	enables = pci_read_config8(dev0, 0x4f);
-	enables |= 0x08;
-	pci_write_config8(dev0, 0x4f, enables);
-	
-	// Set 0x58 to 0x03 to match Award
-	pci_write_config8(dev0, 0x58, 0x03);
-	
-	// enable the ethernet/RTC
-	if(dev0) {
-		enables = pci_read_config8(dev0, 0x51);
-		enables |= 0x18; 
-		pci_write_config8(dev0, 0x51, enables);
+	struct southbridge_via_vt8231_config *conf = dev->chip_info;
+
+	if (!lpc_dev) {
+		/* the first time called, enable devices not on PCI bus
+		 * FIXME: is that device struct there yet? */
+		lpc_dev = dev_find_device(PCI_VENDOR_ID_VIA,
+					  PCI_DEVICE_ID_VIA_8231, 0);
+		if (conf->enable_keyboard)
+			keyboard_on();
+		if (conf->enable_com_ports)
+			com_port_on();
 	}
-	
-	
-	// enable com1 and com2. 
-	if (conf->enable_com_ports) {
-		enables = pci_read_config8(dev0, 0x6e);
-		
-		/* 0x80 is enable com port b, 0x10 is to make it com2, 0x8
-		 * is enable com port a as com1 kevinh/Ispiri - Old code
-		 * thought 0x01 would make it com1, that was wrong enables =
-		 * 0x80 | 0x10 | 0x8 ; pci_write_config8(dev0, 0x6e,
-		 * enables); // note: this is also a redo of some port of
-		 * assembly, but we want everything up.
-		 */
-		
-		/* set com1 to 115 kbaud not clear how to do this yet.
-		 * forget it; done in assembly.
-		 */
-
-	}
-	// enable IDE, since Linux won't do it.
-	// First do some more things to devfn (17,0)
-	// note: this should already be cleared, according to the book. 
-	enables = pci_read_config8(dev0, 0x50);
-	printk_debug("IDE enable in reg. 50 is 0x%x\n", enables);
-	enables &= ~8; // need manifest constant here!
-	printk_debug("set IDE reg. 50 to 0x%x\n", enables);
-	pci_write_config8(dev0, 0x50, enables);
-	
-	// set default interrupt values (IDE)
-	enables = pci_read_config8(dev0, 0x4c);
-	printk_debug("IRQs in reg. 4c are 0x%x\n", enables & 0xf);
-	// clear out whatever was there. 
-	enables &= ~0xf;
-	enables |= 4;
-	printk_debug("setting reg. 4c to 0x%x\n", enables);
-	pci_write_config8(dev0, 0x4c, enables);
-	
-	// set up the serial port interrupts. 
-	// com2 to 3, com1 to 4
-	pci_write_config8(dev0, 0x46, 0x04);
-	pci_write_config8(dev0, 0x47, 0x03);
-	pci_write_config8(dev0, 0x6e, 0x98);
-	//
-	// Power management setup
-	//
-	// Set ACPI base address to IO 0x4000
-	pci_write_config32(devpwr, 0x48, 0x4001);
-	
-	// Enable ACPI access (and setup like award)
-	pci_write_config8(devpwr, 0x41, 0x84);
-	
-	// Set hardware monitor base address to IO 0x6000
-	pci_write_config32(devpwr, 0x70, 0x6001);
-	
-	// Enable hardware monitor (and setup like award)
-	pci_write_config8(devpwr, 0x74, 0x01);
-	
-	// set IO base address to 0x5000
-	pci_write_config32(devpwr, 0x90, 0x5001);
-	
-	// Enable SMBus 
-	pci_write_config8(devpwr, 0xd2, 0x01);
-	
-	//
-	// IDE setup
-	//
-	if (! conf->enable_native_ide) {
-		// Run the IDE controller in 'compatiblity mode - i.e. don't use PCI
-		// interrupts.  Using PCI ints confuses linux for some reason.
-		
-		printk_info("%s: enabling compatibility IDE addresses\n", __FUNCTION__);
-		enables = pci_read_config8(dev1, 0x42);
-		printk_debug("enables in reg 0x42 0x%x\n", enables);
-		enables &= ~0xc0;		// compatability mode
-		pci_write_config8(dev1, 0x42, enables);
-		enables = pci_read_config8(dev1, 0x42);
-		printk_debug("enables in reg 0x42 read back as 0x%x\n", enables);
-	}
-	
-	enables = pci_read_config8(dev1, 0x40);
-	printk_debug("enables in reg 0x40 0x%x\n", enables);
-	enables |= 3;
-	pci_write_config8(dev1, 0x40, enables);
-	enables = pci_read_config8(dev1, 0x40);
-	printk_debug("enables in reg 0x40 read back as 0x%x\n", enables);
-	
-	// Enable prefetch buffers
-	enables = pci_read_config8(dev1, 0x41);
-	enables |= 0xf0;
-	pci_write_config8(dev1, 0x41, enables);
-	
-	// Lower thresholds (cause award does it)
-	enables = pci_read_config8(dev1, 0x43);
-	enables &= ~0x0f;
-	enables |=  0x05;
-	pci_write_config8(dev1, 0x43, enables);
-	
-	// PIO read prefetch counter (cause award does it)
-	pci_write_config8(dev1, 0x44, 0x18);
-	
-	// Use memory read multiple
-	pci_write_config8(dev1, 0x45, 0x1c);
-	
-	// address decoding. 
-	// we want "flexible", i.e. 1f0-1f7 etc. or native PCI
-	// kevinh@ispiri.com - the standard linux drivers seem ass slow when 
-	// used in native mode - I've changed back to classic
-	enables = pci_read_config8(dev1, 0x9);
-	printk_debug("enables in reg 0x9 0x%x\n", enables);
-	// by the book, set the low-order nibble to 0xa. 
-	if (conf->enable_native_ide) {
-		enables &= ~0xf;
-		// cf/cg silicon needs an 'f' here. 
-		enables |= 0xf;
-	} else {
-		enables &= ~0x5;
-	}
-	
-	pci_write_config8(dev1, 0x9, enables);
-	enables = pci_read_config8(dev1, 0x9);
-	printk_debug("enables in reg 0x9 read back as 0x%x\n", enables);
-	
-	// standard bios sets master bit. 
-	enables = pci_read_config8(dev1, 0x4);
-	printk_debug("command in reg 0x4 0x%x\n", enables);
-	enables |= 7;
-	
-	// No need for stepping - kevinh@ispiri.com
-	enables &= ~0x80;
-	
-	pci_write_config8(dev1, 0x4, enables);
-	enables = pci_read_config8(dev1, 0x4);
-	printk_debug("command in reg 0x4 reads back as 0x%x\n", enables);
-	
-	if (! conf->enable_native_ide) {
-		// Use compatability mode - per award bios
-		pci_write_config32(dev1, 0x10, 0x0);
-		pci_write_config32(dev1, 0x14, 0x0);
-		pci_write_config32(dev1, 0x18, 0x0);
-		pci_write_config32(dev1, 0x1c, 0x0);
-		
-		// Force interrupts to use compat mode - just like Award bios
-		pci_write_config8(dev1, 0x3d, 00);
-		pci_write_config8(dev1, 0x3c, 0xff);
-	}
-	
-	
-	/* set up isa bus -- i/o recovery time, rom write enable, extend-ale */
-	pci_write_config8(dev0, 0x40, 0x54);
-	ethernet_fixup();
-	
-	// Start the rtc
-	rtc_init(0);
-}
-
-static void southbridge_init(struct device *dev) {
-	vt8231_init(dev->chip_info);
-	pci_routing_fixup(dev);
-}
-
-struct device_operations vt8231_dev_ops = {
-	.init = &southbridge_init,
-};
-
-static void southbridge_enable(struct device *dev)
-{
-	dev->ops = &vt8231_dev_ops;	
 }
 
 struct chip_operations southbridge_via_vt8231_ops = {
 	CHIP_NAME("VIA vt8231")
-	.enable_dev	= southbridge_enable,
+	.enable_dev	= vt8231_enable,
 };
diff --git a/src/southbridge/via/vt8231/vt8231_early_smbus.c b/src/southbridge/via/vt8231/vt8231_early_smbus.c
index 056c4b5b11..dbb6e213ae 100644
--- a/src/southbridge/via/vt8231/vt8231_early_smbus.c
+++ b/src/southbridge/via/vt8231/vt8231_early_smbus.c
@@ -12,12 +12,12 @@
 #define SMBTRNSADD 0x9
 #define SMBSLVDATA 0xa
 #define SMLINK_PIN_CTL 0xe
-#define SMBUS_PIN_CTL  0xf 
+#define SMBUS_PIN_CTL  0xf
 
 /* Define register settings */
 #define HOST_RESET 0xff
-#define DIMM_BASE 0xa0        // 1010000 is base for DIMM in SMBus
-#define READ_CMD  0x01        // 1 in the 0 bit of SMBHSTADD states to READ
+#define DIMM_BASE 0xa0		// 1010000 is base for DIMM in SMBus
+#define READ_CMD  0x01		// 1 in the 0 bit of SMBHSTADD states to READ
 
 
 #define SMBUS_TIMEOUT (100*1000*10)
@@ -27,29 +27,28 @@ static void enable_smbus(void)
 	device_t dev;
 	unsigned char c;
 	/* Power management controller */
-	dev = pci_locate_device(PCI_ID(0x1106,0x8235), 0);
-	
+	dev = pci_locate_device(PCI_ID(0x1106, 0x8235), 0);
+
 	if (dev == PCI_DEV_INVALID) {
 		die("SMBUS controller not found\r\n");
 	}
-	
 	// set IO base address to SMBUS_IO_BASE
-	pci_write_config32(dev, 0x90, SMBUS_IO_BASE|1);
-	
+	pci_write_config32(dev, 0x90, SMBUS_IO_BASE | 1);
+
 	// Enable SMBus 
 	c = pci_read_config8(dev, 0xd2);
 	c |= 5;
 	pci_write_config8(dev, 0xd2, c);
-	
+
 	/* make it work for I/O ...
 	 */
-	dev = pci_locate_device(PCI_ID(0x1106,0x8231), 0);
+	dev = pci_locate_device(PCI_ID(0x1106, 0x8231), 0);
 	c = pci_read_config8(dev, 4);
 	c |= 1;
 	pci_write_config8(dev, 4, c);
 	print_debug_hex8(c);
 	print_debug(" is the comm register\r\n");
-	
+
 	print_debug("SMBus controller enabled\r\n");
 }
 
@@ -61,52 +60,51 @@ static inline void smbus_delay(void)
 
 static int smbus_wait_until_active(void)
 {
-        unsigned long loops;
-        loops = SMBUS_TIMEOUT;
-        do {
-                unsigned char val;
-                smbus_delay();
-                val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
-                if ((val & 1)) {
-                        break;
-                }
-        } while(--loops);
-        return loops?0:-4;
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned char val;
+		smbus_delay();
+		val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+		if ((val & 1)) {
+			break;
+		}
+	} while (--loops);
+	return loops ? 0 : -4;
 }
 
 static int smbus_wait_until_ready(void)
 {
-        unsigned long loops;
-        loops = SMBUS_TIMEOUT;
-        do {
-                unsigned char val;
-                smbus_delay();
-                val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
-                if ((val & 1) == 0) {
-                        break;
-                }
-                if(loops == (SMBUS_TIMEOUT / 2)) {
-                        outb(inb(SMBUS_IO_BASE + SMBHSTSTAT),
-                                SMBUS_IO_BASE + SMBHSTSTAT);
-                }
-        } while(--loops);
-        return loops?0:-2;
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned char val;
+		smbus_delay();
+		val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+		if ((val & 1) == 0) {
+			break;
+		}
+		if (loops == (SMBUS_TIMEOUT / 2)) {
+			outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+		}
+	} while (--loops);
+	return loops ? 0 : -2;
 }
 
 static int smbus_wait_until_done(void)
 {
-        unsigned long loops;
-        loops = SMBUS_TIMEOUT;
-        do {
-                unsigned char val;
-                smbus_delay();
-
-                val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
-                if ( (val & 1) == 0) {
-                        break;
-                }
-        } while(--loops);
-        return loops?0:-3;
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned char val;
+		smbus_delay();
+
+		val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+		if ((val & 1) == 0) {
+			break;
+		}
+	} while (--loops);
+	return loops ? 0 : -3;
 }
 
 void smbus_reset(void)
@@ -115,13 +113,13 @@ void smbus_reset(void)
 	outb(HOST_RESET, SMBUS_IO_BASE + SMBHSTSTAT);
 	outb(HOST_RESET, SMBUS_IO_BASE + SMBHSTSTAT);
 	outb(HOST_RESET, SMBUS_IO_BASE + SMBHSTSTAT);
-	
+
 	smbus_wait_until_ready();
 	print_debug("After reset status ");
-	print_debug_hex8( inb(SMBUS_IO_BASE + SMBHSTSTAT));
+	print_debug_hex8(inb(SMBUS_IO_BASE + SMBHSTSTAT));
 	print_debug("\r\n");
 }
-  
+
 static void smbus_print_error(unsigned char host_status_register)
 {
 
@@ -152,96 +150,95 @@ static void smbus_print_error(unsigned char host_status_register)
  */
 static int smbus_read_byte(unsigned device, unsigned address)
 {
-        unsigned char global_control_register;
-        unsigned char global_status_register;
-        unsigned char byte;
-
-        if (smbus_wait_until_ready() < 0) {
-          outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
-          if ( smbus_wait_until_ready() < 0 ) {
-              return -2;
-          }
-        }
-
-        /* setup transaction */
-        /* disable interrupts */
-        outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL);
-        /* set the device I'm talking too */
-        outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD);
-        /* set the command/address... */
-        outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
-        /* set up for a byte data read */
-        outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2<<2), SMBUS_IO_BASE + SMBHSTCTL);
-
-        /* clear any lingering errors, so the transaction will run */
-        outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
-
-        /* clear the data byte...*/
-        outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
-
-        /* start a byte read, with interrupts disabled */
-        outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
-        /* poll for it to start */
-        if (smbus_wait_until_active() < 0) {
-                return -4;
-        }
-
-        /* poll for transaction completion */
-        if (smbus_wait_until_done() < 0) {
-                return -3;
-        }
+	unsigned char global_control_register;
+	unsigned char global_status_register;
+	unsigned char byte;
+
+	if (smbus_wait_until_ready() < 0) {
+		outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+		if (smbus_wait_until_ready() < 0) {
+			return -2;
+		}
+	}
+
+	/* setup transaction */
+	/* disable interrupts */
+	outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL);
+	/* set the device I'm talking too */
+	outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD);
+	/* set the command/address... */
+	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
+	/* set up for a byte data read */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2 << 2), SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* clear any lingering errors, so the transaction will run */
+	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+
+	/* clear the data byte... */
+	outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
+
+	/* start a byte read, with interrupts disabled */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
+	/* poll for it to start */
+	if (smbus_wait_until_active() < 0) {
+		return -4;
+	}
+
+	/* poll for transaction completion */
+	if (smbus_wait_until_done() < 0) {
+		return -3;
+	}
 
 	/* Ignore the Host Busy & Command Complete ? */
-        global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~((1<<1)|(1<<0));
+	global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~((1 << 1) | (1 << 0));
 
-        /* read results of transaction */
-        byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
+	/* read results of transaction */
+	byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
 
-        if (global_status_register != 0) {
-                return -1;
-        }
-        return byte;
+	if (global_status_register != 0) {
+		return -1;
+	}
+	return byte;
 }
 
 #if 0
 /* SMBus routines borrowed from VIA's Trident Driver */
 /* this works, so I am not going to touch it for now -- rgm */
-static unsigned char smbus_read_byte(unsigned char devAdr, 
-				unsigned char bIndex) 
+static unsigned char smbus_read_byte(unsigned char devAdr, unsigned char bIndex)
 {
 	unsigned int i;
-	unsigned char  bData;
-	unsigned char  sts = 0;
-	
+	unsigned char bData;
+	unsigned char sts = 0;
+
 	/* clear host status */
 	outb(0xff, SMBUS_IO_BASE);
-	
+
 	/* check SMBUS ready */
-	for ( i = 0; i < SMBUS_TIMEOUT; i++ )
-		if ( (inb(SMBUS_IO_BASE) & 0x01) == 0 )
+	for (i = 0; i < SMBUS_TIMEOUT; i++)
+		if ((inb(SMBUS_IO_BASE) & 0x01) == 0)
 			break;
 
 	/* set host command */
-	outb(bIndex, SMBUS_IO_BASE+3);
-	
+	outb(bIndex, SMBUS_IO_BASE + 3);
+
 	/* set slave address */
-	outb(devAdr | 0x01, SMBUS_IO_BASE+4);
-	
+	outb(devAdr | 0x01, SMBUS_IO_BASE + 4);
+
 	/* start */
-	outb(0x48, SMBUS_IO_BASE+2);
-	
+	outb(0x48, SMBUS_IO_BASE + 2);
+
 	/* SMBUS Wait Ready */
-	for ( i = 0; i < SMBUS_TIMEOUT; i++ )
-		if ( ((sts = inb(SMBUS_IO_BASE)) & 0x01) == 0 )
+	for (i = 0; i < SMBUS_TIMEOUT; i++)
+		if (((sts = inb(SMBUS_IO_BASE)) & 0x01) == 0)
 			break;
 	if ((sts & ~3) != 0) {
 		smbus_print_error(sts);
 		return 0;
 	}
-	bData=inb(SMBUS_IO_BASE+5);
-	
+	bData = inb(SMBUS_IO_BASE + 5);
+
 	return bData;
-	
+
 }
 #endif
 /* for reference, here is the fancier version which we will use at some 
@@ -252,11 +249,11 @@ int smbus_read_byte(unsigned device, unsigned address, unsigned char *result)
 {
 	unsigned char host_status_register;
 	unsigned char byte;
-	
+
 	reset();
-	
+
 	smbus_wait_until_ready();
-	
+
 	/* setup transaction */
 	/* disable interrupts */
 	outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL);
@@ -265,35 +262,32 @@ int smbus_read_byte(unsigned device, unsigned address, unsigned char *result)
 	/* set the command/address... */
 	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
 	/* set up for a byte data read */
-	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x2 << 2),
-		SMBUS_IO_BASE + SMBHSTCTL);
-	
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x2 << 2), SMBUS_IO_BASE + SMBHSTCTL);
+
 	/* clear any lingering errors, so the transaction will run */
 	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
-	
-	/* clear the data byte...*/
+
+	/* clear the data byte... */
 	outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
-	
+
 	/* start the command */
-	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40),
-		SMBUS_IO_BASE + SMBHSTCTL);
-	
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
+
 	/* poll for transaction completion */
 	smbus_wait_until_done();
-	
+
 	host_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT);
-	
+
 	/* Ignore the In Use Status... */
 	host_status_register &= ~(1 << 6);
-	
+
 	/* read results of transaction */
 	byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
 	smbus_print_error(byte);
-	
+
 	*result = byte;
 	return host_status_register != 0x02;
 }
 
 
 #endif
-