via epia; also yh lu tyan.

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

10 files changed, 692 insertions, 3 deletions

diff --git a/src/mainboard/arima/hdama/Config.lb b/src/mainboard/arima/hdama/Config.lb
index 97882302ed..b056124b74 100644
--- a/src/mainboard/arima/hdama/Config.lb
+++ b/src/mainboard/arima/hdama/Config.lb
@@ -15,6 +15,9 @@ uses _ROMBASE
 uses XIP_ROM_SIZE
 uses XIP_ROM_BASE
 
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE 524288
+
 ###
 ### Build options
 ###
@@ -68,9 +71,6 @@ option MAINBOARD_VENDOR="ARIMA"
 ### LinuxBIOS layout values
 ###
 
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 524288
-
 ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
 option ROM_IMAGE_SIZE = 65536
 
diff --git a/src/mainboard/via/epia/Config.lb b/src/mainboard/via/epia/Config.lb
new file mode 100644
index 0000000000..6d30820105
--- /dev/null
+++ b/src/mainboard/via/epia/Config.lb
@@ -0,0 +1,250 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses MAINBOARD
+uses ARCH
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE  524288
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+option HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+option HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+option HAVE_PIRQ_TABLE=1
+option IRQ_SLOT_COUNT=7
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+option HAVE_MP_TABLE=1
+
+##
+## Build code to export a CMOS option table
+##
+option HAVE_OPTION_TABLE=1
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+option CONFIG_SMP=1
+option CONFIG_MAX_CPUS=2
+
+##
+## Build code to setup a generic IOAPIC
+##
+option CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+option MAINBOARD_PART_NUMBER="HDAMA"
+option MAINBOARD_VENDOR="ARIMA"
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+option ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+option STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+option HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+option USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+	option ROM_SECTION_SIZE   = FALLBACK_SIZE
+	option ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+	option ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
+	option ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+option PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+option CONFIG_ROM_STREAM     = 1
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+option _ROMBASE      = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+option XIP_ROM_SIZE=65536
+option XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+
+driver mainboard.o
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c" 
+	action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+end
+
+makerule ./failover.inc
+	depends "./failover.E ./romcc"
+	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+end
+
+makerule ./auto.E 
+	depends	"$(MAINBOARD)/auto.c" 
+	action	"$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+end
+makerule ./auto.inc 
+	depends "./auto.E ./romcc"
+	action	"./romcc   -O ./auto.E > auto.inc"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/i386/entry16.inc
+mainboardinit cpu/i386/entry32.inc
+ldscript /cpu/i386/entry16.lds
+ldscript /cpu/i386/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/i386/reset16.inc 
+	ldscript /cpu/i386/reset16.lds 
+else
+	mainboardinit cpu/i386/reset32.inc 
+	ldscript /cpu/i386/reset32.lds 
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+##
+## Setup our mtrrs
+##
+# mainboardinit cpu/p6/earlymtrr.inc
+
+###
+### This is the early phase of linuxBIOS startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+	ldscript /arch/i386/lib/failover.lds 
+	mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit ./auto.inc
+
+##
+## Include the secondary Configuration files 
+##
+dir /pc80
+config chip.h
+
+northbridge via/vt8601 "vt8601"
+	pci 0:18.0
+	pci 0:18.0
+	pci 0:18.0
+	pci 0:18.1
+	pci 0:18.2
+	pci 0:18.3
+	southbridge via/vt8231 "vt8231"
+		register "enable_usb" = "0"
+		register "enable_native_ide" = "1"
+		register "enable_com_ports" = "1"
+		register "enable_keyboard" = "0"
+		register "enable_nvram" = "1"
+		pci 0:0.0
+		pci 0:0.1
+		pci 0:1.0
+		pci 0:1.1
+	end
+end
+
+cpu p5 "cpu0"
+	
+end
+
+##
+## Include the old serial code for those few places that still need it.
+##
+mainboardinit pc80/serial.inc
+mainboardinit arch/i386/lib/console.inc
+
diff --git a/src/mainboard/via/epia/auto.c b/src/mainboard/via/epia/auto.c
new file mode 100644
index 0000000000..5b8aa0bbdd
--- /dev/null
+++ b/src/mainboard/via/epia/auto.c
@@ -0,0 +1,89 @@
+#define ASSEMBLY 1
+
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <cpu/p6/apic.h>
+#include <arch/io.h>
+#include <device/pnp.h>
+#include <arch/romcc_io.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "northbridge/via/vt8601/raminit.h"
+void udelay(int usecs) {
+  int i;
+  for(i = 0; i < usecs; i++)
+    outb(0x80, 0x80);
+}
+
+#include "lib/delay.c"
+#include "cpu/p6/boot_cpu.c"
+#include "debug.c"
+
+#include "southbridge/via/vt8231/vt8231_early_smbus.c"
+#define SIO_BASE 0x2e
+#define MAXIMUM_CONSOLE_LOGLEVEL 9
+#define DEFAULT_CONSOLE_LOGLEVEL 9
+
+static void memreset_setup(void)
+{
+}
+
+/*
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+*/
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	return smbus_read_byte(device, address);
+}
+
+
+
+#include "northbridge/via/vt8601/raminit.c"
+#include "sdram/generic_sdram.c"
+
+static void main(void)
+{
+  struct mem_controller cpu[1];
+  //	init_timer();
+
+	uart_init();
+	console_init();
+	
+	enable_smbus();
+	memreset_setup();
+	sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
+
+
+	/* Check all of memory */
+#if 0
+	msr_t msr;
+	msr = rdmsr(TOP_MEM);
+	print_debug("TOP_MEM: ");
+	print_debug_hex32(msr.hi);
+	print_debug_hex32(msr.lo);
+	print_debug("\r\n");
+#endif
+#if 0
+	ram_check(0x00000000, msr.lo);
+#endif
+#if 0
+	static const struct {
+		unsigned long lo, hi;
+	} check_addrs[] = {
+		/* Check 16MB of memory @ 0*/
+		{ 0x00000000, 0x01000000 },
+#if TOTAL_CPUS > 1
+		/* Check 16MB of memory @ 2GB */
+		{ 0x80000000, 0x81000000 },
+#endif
+	};
+	int i;
+	for(i = 0; i < sizeof(check_addrs)/sizeof(check_addrs[0]); i++) {
+		ram_check(check_addrs[i].lo, check_addrs[i].hi);
+	}
+#endif
+}
diff --git a/src/mainboard/via/epia/chip.h b/src/mainboard/via/epia/chip.h
new file mode 100644
index 0000000000..9836e2dfa9
--- /dev/null
+++ b/src/mainboard/via/epia/chip.h
@@ -0,0 +1,5 @@
+struct chip_control mainboard_arima_hdama_control;
+
+struct mainboard_arima_hdama_config {
+	int nothing;
+};
diff --git a/src/mainboard/via/epia/cmos.layout b/src/mainboard/via/epia/cmos.layout
new file mode 100644
index 0000000000..5ba4c032c1
--- /dev/null
+++ b/src/mainboard/via/epia/cmos.layout
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+1008         16      h       0        check_sum
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+
+checksums
+
+checksum 392 1007 1008
+
+
diff --git a/src/mainboard/via/epia/debug.c b/src/mainboard/via/epia/debug.c
new file mode 100644
index 0000000000..714fcc5783
--- /dev/null
+++ b/src/mainboard/via/epia/debug.c
@@ -0,0 +1,128 @@
+
+static void print_debug_pci_dev(unsigned dev)
+{
+	print_debug("PCI: ");
+	print_debug_hex8((dev >> 16) & 0xff);
+	print_debug_char(':');
+	print_debug_hex8((dev >> 11) & 0x1f);
+	print_debug_char('.');
+	print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		print_debug_pci_dev(dev);
+		print_debug("\r\n");
+	}
+}
+
+static void dump_pci_device(unsigned dev)
+{
+	int i;
+	print_debug_pci_dev(dev);
+	print_debug("\r\n");
+	
+	for(i = 0; i <= 255; i++) {
+		unsigned char val;
+		if ((i & 0x0f) == 0) {
+			print_debug_hex8(i);
+			print_debug_char(':');
+		}
+		val = pci_read_config8(dev, i);
+		print_debug_char(' ');
+		print_debug_hex8(val);
+		if ((i & 0x0f) == 0x0f) {
+			print_debug("\r\n");
+		}
+	}
+}
+
+static void dump_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		dump_pci_device(dev);
+	}
+}
+#if 0
+static void dump_spd_registers(const struct mem_controller *ctrl)
+{
+	int i;
+	print_debug("\r\n");
+	for(i = 0; i < 4; i++) {
+		unsigned device;
+		device = ctrl->channel0[i];
+		if (device) {
+			int j;
+			print_debug("dimm: "); 
+			print_debug_hex8(i); 
+			print_debug(".0: ");
+			print_debug_hex8(device);
+			for(j = 0; j < 256; j++) {
+				int status;
+				unsigned char byte;
+				if ((j & 0xf) == 0) {
+					print_debug("\r\n");
+					print_debug_hex8(j);
+					print_debug(": ");
+				}
+				status = smbus_read_byte(device, j);
+				if (status < 0) {
+					print_debug("bad device\r\n");
+					break;
+				}
+				byte = status & 0xff;
+				print_debug_hex8(byte);
+				print_debug_char(' ');
+			}
+			print_debug("\r\n");
+		}
+		device = ctrl->channel1[i];
+		if (device) {
+			int j;
+			print_debug("dimm: "); 
+			print_debug_hex8(i); 
+			print_debug(".1: ");
+			print_debug_hex8(device);
+			for(j = 0; j < 256; j++) {
+				int status;
+				unsigned char byte;
+				if ((j & 0xf) == 0) {
+					print_debug("\r\n");
+					print_debug_hex8(j);
+					print_debug(": ");
+				}
+				status = smbus_read_byte(device, j);
+				if (status < 0) {
+					print_debug("bad device\r\n");
+					break;
+				}
+				byte = status & 0xff;
+				print_debug_hex8(byte);
+				print_debug_char(' ');
+			}
+			print_debug("\r\n");
+		}
+	}
+}
+#endif
diff --git a/src/mainboard/via/epia/failover.c b/src/mainboard/via/epia/failover.c
new file mode 100644
index 0000000000..8eeeaef7e1
--- /dev/null
+++ b/src/mainboard/via/epia/failover.c
@@ -0,0 +1,38 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
+#include "northbridge/amd/amdk8/early_ht.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+
+static void main(void)
+{
+	/* Nothing special needs to be done to find bus 0 */
+	/* Allow the HT devices to be found */
+	enumerate_ht_chain(0);
+
+	/* Setup the 8111 */
+	amd8111_enable_rom();
+
+	/* Is this a cpu reset? */
+	if (cpu_init_detected()) {
+		if (last_boot_normal()) {
+			asm("jmp __normal_image");
+		} else {
+			asm("jmp __cpu_reset");
+		}
+	}
+	/* Is this a secondary cpu? */
+	else if (!boot_cpu() && last_boot_normal()) {
+		asm("jmp __normal_image");
+	}
+	/* This is the primary cpu how should I boot? */
+	else if (do_normal_boot()) {
+		asm("jmp __normal_image");
+	}
+}
diff --git a/src/mainboard/via/epia/irq_tables.c b/src/mainboard/via/epia/irq_tables.c
new file mode 100644
index 0000000000..b59ce9f1e9
--- /dev/null
+++ b/src/mainboard/via/epia/irq_tables.c
@@ -0,0 +1,25 @@
+/* This file was generated by getpir.c, do not modify! 
+   (but if you do, please run checkpir on it to verify)
+   Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+   Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+
+const struct irq_routing_table intel_irq_routing_table = {
+	PIRQ_SIGNATURE, /* u32 signature */
+	PIRQ_VERSION,   /* u16 version   */
+	32+16*18,        /* there can be total 18 devices on the bus */
+	1,           /* Where the interrupt router lies (bus) */
+	0x23,           /* Where the interrupt router lies (dev) */
+	0,         /* IRQs devoted exclusively to PCI usage */
+	0x0,         /* Vendor */
+	0x0,         /* Device */
+	0,         /* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0x35,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+	}
+};
diff --git a/src/mainboard/via/epia/mainboard.c b/src/mainboard/via/epia/mainboard.c
new file mode 100644
index 0000000000..6790aaca1b
--- /dev/null
+++ b/src/mainboard/via/epia/mainboard.c
@@ -0,0 +1,37 @@
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+
+#include <arch/io.h>
+#include <device/chip.h>
+#include "../../../northbridge/amd/amdk8/northbridge.h"
+#include "chip.h"
+
+
+static struct device_operations mainboard_operations = {
+	.read_resources   = root_dev_read_resources,
+	.set_resources    = root_dev_set_resources,
+	.enable_resources = enable_childrens_resources,
+	.init             = 0,
+	.scan_bus         = vt8_scan_root_bus,
+	.enable           = 0,
+};
+
+static void enumerate(struct chip *chip)
+{
+	struct chip *child;
+	dev_root.ops = &mainboard_operations;
+	chip->dev = &dev_root;
+	chip->bus = 0;
+	for(child = chip->children; child; child = child->next) {
+		child->bus = &dev_root.link[0];
+	}
+}
+struct chip_control mainboard_via_epia_control = {
+	.enumerate = enumerate, 
+	.name      = "Arima HDAMA mainboard ",
+};
+
diff --git a/src/mainboard/via/epia/reset.c b/src/mainboard/via/epia/reset.c
new file mode 100644
index 0000000000..5796e17dc8
--- /dev/null
+++ b/src/mainboard/via/epia/reset.c
@@ -0,0 +1,43 @@
+#if 0
+//#include "arch/romcc_io.h"
+#include <arch/io.h>
+
+typedef unsigned device_t;
+
+#define PCI_DEV(BUS, DEV, FN) ( \
+	(((BUS) & 0xFF) << 16) | \
+	(((DEV) & 0x1f) << 11) | \
+	(((FN)  & 0x7) << 8))
+
+static void pci_write_config8(device_t dev, unsigned where, unsigned char value)
+{
+        unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outb(value, 0xCFC + (addr & 3));
+}
+
+static void pci_write_config32(device_t dev, unsigned where, unsigned value)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outl(value, 0xCFC);
+}
+
+static unsigned pci_read_config32(device_t dev, unsigned where)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        return inl(0xCFC);
+}
+
+#include "../../../northbridge/amd/amdk8/reset_test.c"
+
+void hard_reset(void)
+{
+	set_bios_reset();
+	pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+}
+#endif