#Uncommenting these urls would only enable
#the power up auto injection and force injection(test case).
#XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra2.bin
#XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra2.bin
#XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra2.bin

#Version check for XTRA
#DISABLE = 0
#AUTO    = 1
#XTRA2   = 2
#XTRA3   = 3
XTRA_VERSION_CHECK=0

XTRA_TEST_ENABLED = 1
XTRA_THROTTLE_ENABLED = 0



# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0

#NTP server
NTP_SERVER=time.izatcloud.net

#XTRA CA path
XTRA_CA_PATH=/system/etc/security/cacerts

# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
#               4 - Debug, 5 - Verbose
# If DEBUG_LEVEL is commented, Android's logging levels will be used
DEBUG_LEVEL = 5

# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0

# Below bit mask configures how GPS functionalities
# should be locked when user turns off GPS on Settings
# Set bit 0x1 if MO GPS functionalities are to be locked
# Set bit 0x2 if NI GPS functionalities are to be locked
# default - non is locked for backward compatibility
#GPS_LOCK = 0

# supl version 1.0
SUPL_VER=0x20000

# Emergency SUPL, 1=enable, 0=disable
#SUPL_ES=0

#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0

#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will overwrite the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#SUPL_MODE=

# GPS Capabilities bit mask
# SCHEDULING = 0x01
# MSB = 0x02
# MSA = 0x04
# ON_DEMAND_TIME = 0x10
# GEOFENCE = 0x20
# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE
CAPABILITIES=0x37

# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000

################################
##### AGPS server settings #####
################################

# FOR SUPL SUPPORT, set the following
SUPL_HOST=supl.qxwz.com
SUPL_PORT=7275

# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234

# Bitmask of slots that are available
# for write/install to, where 1s indicate writable,
# and the default value is 0 where no slots
# are writable. For example, AGPS_CERT_WRITABLE_MASK
# of b1000001010 makes 3 slots available
# and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0

####################################
#  LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default)
# 1: Enable LPP_User_Plane on LTE
# 2: Enable LPP_Control_Plane
# 3: Enable both LPP_User_Plane and LPP_Control_Plane
LPP_PROFILE = 3

################################
# EXTRA SETTINGS
################################
# NMEA provider (1=Modem Processor, 0=Application Processor)
NMEA_PROVIDER=0
# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
SGLTE_TARGET=0

##################################################
# Select Positioning Protocol on A-GLONASS system
##################################################
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
A_GLONASS_POS_PROTOCOL_SELECT = 0

##################################################
# Select technology for LPPe Control Plane
##################################################
# 0x1: DBH for LPPe CP
# 0x2: WLAN AP Measurements for LPPe CP
# 0x4: SRN AP measurement for CP
# 0x8: Sensor Barometer Measurement LPPe CP
LPPE_CP_TECHNOLOGY = 0

##################################################
# Select technology for LPPe User Plane
##################################################
# 0x1: DBH for LPPe UP
# 0x2: WLAN AP Measurements for LPPe UP
# 0x4: SRN AP measurement for UP
# 0x8: Sensor Barometer Measurement LPPe UP
LPPE_UP_TECHNOLOGY = 0

##################################################
# AGPS_CONFIG_INJECT
##################################################
# enable/disable injection of AGPS configurations:
#     SUPL_VER
#     SUPL_HOST
#     SUPL_PORT
#     C2K_HOST
#     C2K_PORT
#     LPP_PROFILE
#     A_GLONASS_POS_PROTOCOL_SELECT
# 0: disable
# 1: enable
AGPS_CONFIG_INJECT = 1

##################################################
# GNSS settings for automotive use cases
# Configurations in following section are
# specific to automotive use cases, others
# please do not change, keep the default values
##################################################

# AP Coarse Timestamp Uncertainty
##################################################
# default : 10
# AP time stamp uncertainty, until GNSS receiver
# is able to acquire better timing information
AP_TIMESTAMP_UNCERTAINTY = 10

##################################################
# QDR engine availability status
##################################################
# 0 : NO QDR (default)
# 1 : QDR enabled
# This settings enables QDR Configuration for
# automotive use case, if enabled then
# DR_AP_Service needs to be enabled in izat.conf
#EXTERNAL_DR_ENABLED = 0

#####################################
# DR_SYNC Pulse Availability
#####################################
# 0 : DR_SYNC pulse not available (default)
# 1 : DR_SYNC pulse available
# This configuration enables the driver to make use
# of PPS events generated by DR_SYNC pulse
# Standard Linux PPS driver needs to be enabled
DR_SYNC_ENABLED = 0

#####################################
# PPS Device name
#####################################
PPS_DEVICENAME = /dev/pps0

#####################################
# AP Clock Accuracy
#####################################
# Quality of APPS processor clock (in PPM).
# Value specified is used for calculation of
# APPS time stamp uncertainty
AP_CLOCK_PPM = 100

#####################################
# MAX ms difference to detect missing pulse
#####################################
# Specifies time threshold in ms to validate any missing PPS pulses
MISSING_PULSE_TIME_DELTA = 900

#####################################
# Propagation time uncertainty
#####################################
# This settings enables time uncertainty propagation
# logic incase of missing PPS pulse
PROPAGATION_TIME_UNCERTAINTY = 1