###################### Start of libnfc-brcm.conf #######################

###############################################################################
# Application options
APPL_TRACE_LEVEL=0xFF
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF

###############################################################################
# File used for NFA storage
NFA_STORAGE="/data/nfc"

###############################################################################
# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
NFC_WAKE_DELAY=20

###############################################################################
# LPTD mode configuration
#  byte[0] is the length of the remaining bytes in this value
#     if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
#  byte[1] is the param id it should be set to B9.
#  byte[2] is the length of the LPTD parameters
#  byte[3] indicates if LPTD is enabled
#     if set to 0, LPTD will be disabled (parameters will still be sent).
#  byte[4-n] are the LPTD parameters.
#  By default, LPTD is enabled and default settings are used.
#  See nfc_hal_dm_cfg.c for defaults
LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00}

###############################################################################
# Startup Configuration (100 bytes maximum)
#
# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is
#    for UICC1.  The values are defined as:
#   0 : UICCx only supports ISO_DEP in low power mode.
#   2 : UICCx only supports Mifare in low power mode.
#   3 : UICCx supports both ISO_DEP and Mifare in low power mode.
#
#                                                                          AA BB
NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01}

###############################################################################
# Configure the default Destination Gate used by HCI (the default is 4, which
# is the ETSI loopback gate.
NFA_HCI_DEFAULT_DEST_GATE=0xF0

###############################################################################
# Configure the NFC Extras to open and use a static pipe.  If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
# for each UICC (where F3="UICC0" and F4="UICC1")
#NFA_HCI_STATIC_PIPE_ID_F3=0x70
#NFA_HCI_STATIC_PIPE_ID_01=0x19
NFA_HCI_STATIC_PIPE_ID_C0=0x19

###############################################################################
# When disconnecting from Oberthur secure element, perform a warm-reset of
# the secure element to deselect the applet.
# The default hex value of the command is 0x3.  If this variable is undefined,
# then this feature is not used.
OBERTHUR_WARM_RESET_COMMAND=0x03

###############################################################################
# Force UICC to only listen to the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
UICC_LISTEN_TECH_MASK=0x07

###############################################################################
# Force HOST listen feature enable or disable.
# 0: Disable
# 1: Enable
HOST_LISTEN_ENABLE=0x01

###############################################################################
# Enabling/Disabling Forward functionality
# Disable           0x00
# Enable            0x01
NXP_FWD_FUNCTIONALITY_ENABLE=0x01

###############################################################################
# Allow UICC to be powered off if there is no traffic.
# Timeout is in ms. If set to 0, then UICC will not be powered off.
#UICC_IDLE_TIMEOUT=30000
UICC_IDLE_TIMEOUT=0

###############################################################################
# AID for Empty Select command
# If specified, this AID will be substituted when an Empty SELECT command is
# detected.  The first byte is the length of the AID.  Maximum length is 16.
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}

###############################################################################
# When screen is turned off, specify the desired power state of the controller.
# 0: power-off-sleep state; DEFAULT
# 1: full-power state
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
SCREEN_OFF_POWER_STATE=1

###############################################################################
# Firmware patch file
#  If the value is not set then patch download is disabled.
FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"

###############################################################################
# Firmware pre-patch file (sent before the above patch file)
#  If the value is not set then pre-patch is not used.
FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"

###############################################################################
# Insert a delay in microseconds per byte after a write to NFCC.
# after writing a block of data to the NFCC, delay this an amopunt of time before
# writing next block of data.  the delay is calculated as below
#   NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
NFC_WRITE_DELAY=20

###############################################################################
# Force tag polling for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
#            NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
#            NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO |
#            NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE.
#
# Notable bits:
# NFA_TECHNOLOGY_MASK_A             0x01    /* NFC Technology A             */
# NFA_TECHNOLOGY_MASK_B             0x02    /* NFC Technology B             */
# NFA_TECHNOLOGY_MASK_F             0x04    /* NFC Technology F             */
# NFA_TECHNOLOGY_MASK_ISO15693      0x08    /* Proprietary Technology       */
# NFA_TECHNOLOGY_MASK_KOVIO         0x20    /* Proprietary Technology       */
# NFA_TECHNOLOGY_MASK_A_ACTIVE      0x40    /* NFC Technology A active mode */
# NFA_TECHNOLOGY_MASK_F_ACTIVE      0x80    /* NFC Technology F active mode */
POLLING_TECH_MASK=0xEF

###############################################################################
# Force P2P to only listen for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
#            NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
#
# Notable bits:
# NFA_TECHNOLOGY_MASK_A             0x01    /* NFC Technology A             */
# NFA_TECHNOLOGY_MASK_F             0x04    /* NFC Technology F             */
# NFA_TECHNOLOGY_MASK_A_ACTIVE      0x40    /* NFC Technology A active mode */
# NFA_TECHNOLOGY_MASK_F_ACTIVE      0x80    /* NFC Technology F active mode */
P2P_LISTEN_TECH_MASK=0xC5

PRESERVE_STORAGE=0x01

###############################################################################
# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h.
# The value is set to 3 by default as it assumes we will discover 0xF2,
# 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced
# so that the stack will not wait any longer than necessary.

# Maximum EE supported number
# NXP PN547C2 0x02
# NXP PN65T 0x03
# NXP PN548C2 0x02
# NXP PN66T 0x03
NFA_MAX_EE_SUPPORTED=0x02

###############################################################################
# NCI Hal Module name
NCI_HAL_MODULE="nfc_nci"

###############################################################################
# AID_MATCHING constants
# AID_MATCHING_EXACT_ONLY 0x00
# AID_MATCHING_EXACT_OR_PREFIX 0x01
# AID_MATCHING_PREFIX_ONLY 0x02
AID_MATCHING_MODE=0x01

###############################################################################
# Default Secure Element route id
DEFAULT_OFFHOST_ROUTE=0x02

###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
#  byte[0] NCI_PROTOCOL_18092_ACTIVE
#  byte[1] NCI_PROTOCOL_B_PRIME
#  byte[2] NCI_PROTOCOL_DUAL
#  byte[3] NCI_PROTOCOL_15693
#  byte[4] NCI_PROTOCOL_KOVIO
#  byte[5] NCI_PROTOCOL_MIFARE
#  byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
#  byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
#  byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:77:FF:FF}

###############################################################################
# Bail out mode
#  If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
NFA_POLL_BAIL_OUT_MODE=0x01

################################################################################
# Set max transceive length for IsoDep frames
# Standard      0x105 (261)
# Extended      0xFEFF (65279)
ISO_DEP_MAX_TRANSCEIVE=0xFEFF

#################################################################################
# Enable/Disable NFC-F HCE
# Disable       0x00
# Enable        non-zero value
ENABLE_NFCF_HCE=0x00