#######################################################################################
# Common configurations (applies to both V4L2 & non-V4L2)
#######################################################################################

# UART device port where Bluetooth controller is attached (default ttyS1)
UartPort = /dev/brcm_bt_drv
UimUartPort = /dev/ttyHS0

# Target Baudrate to change to if different from 3000000
# This entry is mandatory if using V4L2
UartBaudRate = 3000000

# Firmware patch file location (compile default /vendor/firmware)
FwPatchFilePath = /system/etc/firmware

# uncomment if you want to load a specific version
FwPatchFileName = BCM43xx.hcd

# Firmware patch setttlement delay in millisec
# This entry is mandatory if using V4L2
FwPatchSettlementDelay = 100

# host/bt wake polarity to match with kernel settings
# 0: active low (negative logic)
# 1: active high (positive logic) (default)
LpmWakePolarity = 1

# stack/controller idle timeout in units (300/25ms)
# make sur controller supports 25ms
#LpmIdleTimeout = 2

#**************************************
# SCO I2S/PCM interface
#   0: PCM
#   1: I2S
#**************************************
#ScoInterface = 0

#**************************************
# SCO over PCM
#
# Configuration for SCO over PCM interface, which parameters are represented by array.
# Each PCM parameters' definations are listed as below, in order. Be NOTICED that
# this setting is ONLY VALID as PCM interface is selected/used.
#
#  PCM Frame Type (SCO_PCM_IF_FRAME_TYPE)
#   - 0: Short
#   - 1: Long
#
#  PCM Sync Mode (SCO_PCM_IF_SYNC_MODE)
#   - 0: Slave
#   - 1: Master
#
#  PCM Clock Mode (SCO_PCM_IF_CLOCK_MODE)
#   - 0: Slave
#   - 1: Master
#
#  PCM NBS(Narrow Band Speech) Clock Rate (SCO_PCM_IF_CLOCK_RATE)
#   - 0:  128K
#   - 1:  256K
#   - 2:  512K
#   - 3: 1024K
#   - 4: 2048K
#
#  PCM WBS(Wide Band Speech) Clock Rate (SCO_I2SPCM_IF_CLOCK_RATE4WBS)
#   - 0:  128K
#   - 1:  256K
#   - 2:  512K
#   - 3: 1024K
#   - 4: 2048K
#
# PCM WBS (Wide Band Speech) Sample Rate (SCO_I2SPCM_IF_SAMPLE_RATE)
#
#   - 0: 8K
#   - 1: 16K
#   - 2: 4K
#
#    Carriers do not support 16K voice samples at present,
#    so, setting PCM WBS Sample Rate to 8K (0) for now.
#
#**************************************
#ScoPCMifParams = {0,0,0,4,4,0}

#**************************************
# PCM Format
#
# Configuration for PCM format, which parameters are represented by array.
# Each PCM format parameters' definations/descriptions are listed as below, in order.
#
#  Shift Mode (PCM_DATA_FMT_SHIFT_MODE)
#   - 0: MSB first
#   - 1: LSB first
#
#  Fill Bits (PCM_DATA_FMT_FILL_BITS)
#   - Specifies the value with which to fill unused bits
#     if Fill_Method is set to programmable
#
#  Fill Method (PCM_DATA_FMT_FILL_METHOD)
#   - 0 : 0's
#   - 1 : 1's
#   - 2 : Signed
#   - 3 : Programmable
#
#  Fill Num (PCM_DATA_FMT_FILL_NUM)
#   - Specifies the number of bits to be filled
#
#  Justify Mode (PCM_DATA_FMT_JUSTIFY_MODE)
#   - 0: Left justify (fill data shifted out last)
#   - 1: Right justify (fill data shifted out first)
#
#**************************************
#ScoPCMFmtParams = {0,0,3,0,0}

#######################################################################################

#######################################################################################
# Configurations specific to V4L2 based solution
#######################################################################################

# Setting this to true enables Low Power Mode (LPM) in the shared
# line discipline driver. Set this to fale if the LPM is not
# enabled or if it is handled in the platform
LpmEnable=true

#For hammerhead and grouper LPM is through bluesleep
#LPM for maguro and manta is done by UART driver itself
LpmUseBluesleep=false

#Set to true if bd address was programmed into firmware using OTP
UseControllerBdaddr=false

#Enable debugging (add values below to enable multiple options)
# enable logging in driver for init/release driver      : 1
# enable logging in driver for open                     : 2
# enable logging in driver for close                    : 4
# enable logging in driver for Tx                       : 8
# enable logging in driver for Rx                       : 16
DBG_BT_DRV = 31
DBG_LDISC_DRV = 31
DBG_FM_DRV = 31
#***************************************************************************

#######################################################################################